Carly Coding for BMW X1

Panic alarm with remote
• active
• off
Press and hold the ‘unlock trunk’ button to trigger the alarm. To activate this function, also activate ‘Panic alarm’ in the DWA module. (codable in CAS)

Arm/Disarm Anti-Theft Alarm System
• Only with remote
• With locks and remote
Anti-theft alarm system is armed/disarmed by locking/unlocking the car (1) with the locks and the remote or (2) only by locking/unlocking the car with the remote. (codable in CAS)

Panic alarm
• on
• off
Trigger alarm by pressing and holding the ‘unlock tailgate’ button on the remote. To activate this function also activate ‘Panic alarm with remote’ in the CAS module. (codable in DWA)

Audible confirmation – locking vehicle
• on
• off
Audible confirmation for locking vehicle is active/not active. (codable in DWA)

Audible confirmation – unlocking vehicle
• on
• off
Audible confirmation for unlocking vehicle is active/not active. (codable in DWA)

Alarm with dimmed headlights
• on
• off
Dimmed headlights blink when alarm is initiated. (codable in DWA)

Alarm with high beams
• on
• off
High beams blink when alarm is initiated. (codable in DWA)

Alarm with warning lights
• on
• off
Warning lights blink when alarm is initiated. (codable in DWA)

Alarm type
• Europe
• USA
• UK
Type and sound of the alarm. United Kingdom is the same sound as Europe, the duration of the alarm is eight times longer. (codable in DWAS)

Audible confirmation
• on
• off
Enable menus for audible confirmation for locking/unlocking the vehicle in the iDrive. The menu can be found in the same menu as the other locking confirmation settings in the iDrive. Only works if an ‘Anti Theft Alarm System’ is installed, because the sound is generated by the siren of the anti theft alarm system and not by the horn. If you are not sure, whether an ‘Anti Theft Alarm System’ or only the standard ‘Anti Theft Protection’ is installed, please perform a diagnostic session. You can then check if the module for the anti theft alarm system was found or not. (codable in CCC)

Audible confirmation – unlocking vehicle
• on
• off
Display option for audible confirmation for unlocking the vehicle in the iDrive. Please enable ‘Audible confirmation’ for this as well in this module and carefully read the description for it. (codable in CCC)

Audible confirmation – locking vehicle 1/2
• on
• off
Display option for audible confirmation for locking the vehicle in the iDrive. Please enable ‘Audible confirmation’ for this as well in this module and carefully read the description for it. (codable in CCC)

Audible confirmation – locking vehicle 2/2
• on
• off
Only change this function with ‘Audible confirmation – locking vehicle 1/2’. (codable in CCC)

Daytime running lights – angel eyes
• on
• off
Use angel eyes as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’ and ‘Daytime running lights – customization’ to ‘Only additional lights’. If you want to increase the brightness, please use ’Daytime running lights – angel eyes brightness’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Angel eyes brightness daytime running lights
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes (Corona rings) for daytime running lights. (codable in FRM)

Angel eyes brightness standing lights
• off
• very low
• low
• medium
• high
• very high
Brightness of Angel Eyes (Corona rings) for standing lights. (codable in FRM)

Angel eyes brightness parking lights
• off
• very low
• low
• medium
• high
• very high
Brightness of Angel Eyes (Corona rings) for parking lights. (codable in FRM)

Brightness of Angel Eyes 1 – alternative
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes. Only use this coding if the standard codings did not work. (codable in FRM)

Brightness of Angel Eyes 2 – alternative
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes when low beams are active. Only use this coding if the standard codings did not work. (codable in FRM)

Brightness of Angel Eyes 3 – alternative
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes when low beams are active. Only use this coding if the standard codings did not work. (codable in FRM)

Brake force display
• on
• off
Customized brake lights turn on or flash when braking hard. Use the codings below to customize the brake force display. (codable in FRM)

Brake force display 1/2
• on
• on (alternative)
Customized brake lights turn on or flash when braking hard. Use the codings below to customize the brake force display. To activate this function, set ‘Brake force display 2/2’ to ‘active’. (codable in FRM)

Brake force display 2/2
• on
• on (alternative)
• off
Only change this function with ‘Brake force display 1/2’. (codable in FRM)

Brake force display – minimum speed
• 20 kph / 12 mph
• 50 kph / 31 mph
Minimum speed threshold for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Brake force display – blinking speed
• slow
• fast
Blinking speed for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Brake force display – angel eyes
• off
• on
• flashing
Customization for angel eyes for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Brake force display – outer brake lights
• off
• on
• flashing
Customization for outer brake lights for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Brake force display – inner brake lights
• on
• flashing
Customization for inner brake lights for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Brake force display – third brake light
• off
• on
• flashing
Customization for third brake lights (rear window) for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Brake force display – tail lights
• off
• on
• flashing
Customization for tail lights for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Brake force display – rear fog lights
• off
• on
• flashing
Customization for rear fog lights for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in FRM)

Wiping interval standstill
• 3s
• 5s
Interval in seconds for windscreen wipers at standstill. (codable in JBBF)

Wiping interval rear window
• off
• 2s
• 4s
• 6s
• 8s
• 12s
Interval in seconds for windscreen rear window wipers. (codable in JBBF)

Rear wiper in reverse gear
• on
• off
Rear wiper automatically turns on in reverse gear when front wipers are active. (codable in JBBF)

Windscreen wipers continue
• on
• off
Windscreen wipers don’t stop in the middle of the windscreen when ignition is turned off. Instead they complete their wiping cycle. (codable in JBBF)

Wipe delay after windowscreen cleaning
• 0.1s
• 0.3s
• 0.5s
• 0.7s
Windscreen wipers wipe 0.x seconds after windscreen is cleaned. (codable in JBBF)

Wipe delay after rear window cleaning
• 0.1s
• 0.3s
• 0.5s
• 0.7s
Rear window wipers wipe 0.x seconds after rear window is cleaned. (codable in JBBF)

Number of wipes after windscreen cleaning
• 1
• 2
• 3
• 4
Number of wipes after windscreen is cleaned. (codable in JBBF)

Number of wipes after rear window cleaning
• 1
• 2
• 3
• 4
Number of wipes after rear window is cleaned. (codable in JBBF)

Head light cleaning
• on
• off
Turn head light cleaning on/off. (codable in JBBF)

Number until headlight cleaning
• 3
• 5
• 7
Head lights are cleaned every x-th time the windscreen washer has been activated. (codable in JBBF)

Number of splashes for head lights
• 2
• 3
Number of splashes for cleaning the head lights. (codable in JBBF)

Length of splash for head lights
• 0.7s
• 1s
• 0.5s
Length of a single splash for head light cleaning. (codable in JBBF)

Delay between splashes for head lights
• 1.3s
• 1s
• 1.5s
Delay between splashes for head light cleaning. (codable in JBBF)

GPS time correction
• on
• off
Time of day is corrected by using GPS. (codable in KOMBI)

Comfort start
• on
• off
Ignition key just has to be tapped once to start the engine after ignition is turned on. (codable in CAS)

Comfort eject
• on
• off
Turn off the ignition with a long press on the start/stop button in order to eject the ignition key. (codable in CAS)

Comfort open using remote
• on
• off
Press and hold the unlock button on the remote to open all windows and the sunroof. (codable in CAS)

Comfort close using remote
• on
• off
Press and hold the lock button on the remote to close all windows and the sunroof. (codable in CAS)

Comfort open using keylocks
• on
• off
Unlock the car by key and hold the key in the unlock position to open all windows and the sunroof. (codable in CAS)

Comfort close using keylocks
• on
• off
Lock the car by key and hold the key in the lock position to close all windows and the sunroof. (codable in CAS)

Comfort close – door (comfort access)
• on
• off
Use comfort closing features when locking with the door handle. This only works if comfort access is installed. Touch the locking area on the door handle for a longer time to close all windows and the sunroof. (codable in CAS)

Comfort folding for sideview mirrors
• on
• off
When holding the lock/unlock button on the remote the sideview mirrors automatically fold/unfold. To activate this function please activate ‘Comfort folding/unfolding for sideview mirrors’ in the ‘FRM’ module. Also activate ‘Comfort open using remote’ and ‘Comfort close using remote’ in this module. (codable in CAS)

Comfort closing delay (mirrors)
• 0.0s
• 0.5s
• 1.5s
General delay for comfort closing. If ‘0.0s’ is set, mirrors fold immediately when car is locked. (codable in CAS)

Deactivate comfort access
• on
• off
In order to deactivate the comfort access, set this coding to ‘not active’. This coding cannot be used to activate a retrofitted comfort access. When the comfort access is deactivated, neither closing nor opening the car via the door handle will work. Turning the ignition and engine on/off without putting the key into the ignition (also known as ‘Keyless Go’) will also not work anymore. Therefore the car cannot be stolen anymore by tricking the comfort access. In order to activate comfort access again, please set this coding to ‘active’. (codable in CAS)

Activate follow me home lights
• on
• off
Follow me home lights are active/not active. (codable in FRM)

Follow me home lights with remote
• on
• off
Quickly press the ‘Open trunk’ button twice to activate the follow me home lights. In some circumstances the function ‘Panic mode remote’ in the CAS has to be activated, too. (codable in FRM)

Cancel follow me home lights
• on
• off
Follow me home lights are cancelled, when activating the flash to pass again. (codable in FRM)

Extend follow me home lights
• on
• off
Follow me home lights are displayed longer, when activating the flash to pass again. (codable in FRM)

Follow me home lights duration
• off
• 40s
• 90s
• 150s
• 240s
Duration of follow me home lights in seconds. To activate follow me home lights, activate the flash to pass, while the enginge is off. (codable in FRM)

Follow me home lights duration Key 1
• off
• 40s
• 90s
• 150s
• 240s
Separate setting for duration in seconds of follow me home lights for key 1. (codable in FRM)

Follow me home lights duration Key 2
• off
• 40s
• 90s
• 150s
• 240s
Separate setting for duration in seconds of follow me home lights for key 2. (codable in FRM)

Follow me home lights duration Key 3
• off
• 40s
• 90s
• 150s
• 240s
Separate setting for duration in seconds of follow me home lights for key 3. (codable in FRM)

Speed limit roof open/close
• 6 kph / 4 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
Speed limit for closing/opening the roof while driving. For pre-facelift models 30 kph is recommended, due to the less stable construction of the roof. (codable in CTM)

Corner LEDs
• on
• off
Corner LEDs are active/not active – also known as ‘Corner Delete Mod’. This function often only works on US models to deactivate the corner LEDs. (codable in FRM)

Corner LEDs brightness – low beams
• off
• low
• medium
• high
Brightness of corner LEDs when low beams are active. (codable in FRM)

Corner LEDs brightness – high beams
• off
• low
• medium
• high
Brightness of corner LEDs when high beams are active. (codable in FRM)

Cornering lights 1/3
• on
• off
Use front fog lights/high beams as cornering lights. Also, this function often requires adaptive headlights to be installed. (codable in FRM)

Cornering lights 2/3
• on
• off
Only change this function with ‘Cornering lights 1/3’. Also, this function often requires adaptive headlights to be installed. (codable in FRM)

Cornering lights 3/3
• on
• off
Only change this function with ‘Cornering lights 1/3’. Also, this function often requires adaptive headlights to be installed. (codable in FRM)

Cornering lights – front fog lights
• on
• off
Front fog lights are used as cornering lights. Only works if ‘Cornering lights’ is also activated. (codable in FRM)

Cornering lights – reverse gear
• on
• off
Use cornering lights also when reversing. Only works if ‘Cornering lights’ is also activated. (codable in FRM)

Cornering lights – brightness
• off
• very low
• low
• medium
• high
• very high
Brightness of ‘Cornering lights’. Only works if ‘Cornering lights’ is also activated. (codable in FRM)

Cornering lights – key 1
• on
• off
Cornering lights are active/not active. Separate setting for ‘Cornering lights’ for key 1. Only works if ‘Cornering lights’ is also activated. (codable in FRM)

Cornering lights – key 2
• on
• off
Cornering lights are active/not active. Separate setting for ‘Cornering lights’ for key 2. Only works if ‘Cornering lights’ is also activated. (codable in FRM)

Cornering lights – key 3
• on
• off
Cornering lights are active/not active. Separate setting for ‘Cornering lights’ for key 3. Only works if ‘Cornering lights’ is also activated. (codable in FRM)

Cornering lights – key 4
• on
• off
Cornering lights are active/not active. Separate setting for ‘Cornering lights’ for key 4. Only works if ‘Cornering lights’ is also activated. (codable in FRM)

Cornering Light
• on
• off
Display menu for activating cornering light in the iDrive. The menu can be found in the same menu as the other light settings in the iDrive. Also, cornering light often requires adaptive headlights to be installed. (codable in CCC)

Daytime running lights in OBC
• on
• off
Turn daytime running lights on/off in on board computer. Might not work if an iDrive system is installed. (codable in KOMBI)

Daytime running lights 1/2
• on
• off
Daytime running lights (DRL) is active/not active. The DRL is activated when the light switch is set to position ‘0’ in the car. Please activate ‘Daytime running lights 2/2’ as well. (codable in FRM)

Daytime running lights 2/2
• on
• off
Daytime running lights (DRL) is active/not active. The DRL is activated when the light switch is set to position ‘0’ in the car. Please activate ‘Daytime running lights 1/2’ as well. (codable in FRM)

Daytime running lights – Key 1
• on
• off
Daytime running lights are active/not active. Separate setting for ‘Daytime running lights’ for key 1. (codable in FRM)

Daytime running lights – Key 2
• on
• off
Daytime running lights are active/not active. Separate setting for ‘Daytime running lights’ for key 2. (codable in FRM)

Daytime running lights – Key 3
• on
• off
Daytime running lights are active/not active. Separate setting for ‘Daytime running lights’ for key 3. (codable in FRM)

Daytime running lights customization
• off
• dimmed turn signals
• dimmed high beams
Customization of the daytime running lights. Brightness can be set with ‘Daytime running lights brightness’. (codable in FRM)

Daytime running lights brightness
• very low
• low
• medium
• high
• very high
Brightness for dimmed daytime running lights. To use this function, also activate ‘Daytime running lights customization’. (codable in FRM)

Daytime running lights – customization
• Off
• Low beams
• High beams
• Only additional lights (EU models)
• Only additional lights (US models)
Customization of the daytime running lights (DRL). The DRL is activated when the light switch is set to position ‘0’ in the car. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – high beams brightness
• off
• very low
• low
• medium
• high
• very high
Brightness of high beams for daytime running lights. To activate the high beams for daytime running lights, set ‘Daytime running lights – customization’ to ‘High beams’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – front fog lights
• on
• off
Use front fog lights as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – front fog lights brightness
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness for ‘Daytime running lights – front fog lights’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – front turn signals
• on
• off
Use front turn signals as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – angel eyes
• on
• off
Use angel eyes as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’ and ‘Daytime running lights – customization’ to ‘Only additional lights’. If you want to increase the brightness, please use ’Daytime running lights – angel eyes brightness’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Angel eyes brightness daytime running lights
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes (Corona rings) for daytime running lights. (codable in FRM)

Daytime running lights – sidemarker
• on
• off
Use sidemarkers as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – number plate lighting
• on
• off
Use number plate lighting as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – tail lights
• on
• off
Use tail lights as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – inner brake lights
• on
• off
Use inner brake lights as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Daytime running lights – 3rd brake lights
• on
• off
Use 3rd brake lights as daytime running lights. To activate this function, set ‘Daytime running lights’ to ‘active’. This coding is only available for cars with an FRM2 or FRM3. These FRM versions started to be installed after ca. 06/2007 in the X1 (E84). (codable in FRM)

Brightness of Angel Eyes 1 – alternative
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes. Only use this coding if the standard codings did not work. (codable in FRM)

Brightness of Angel Eyes 2 – alternative
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes when low beams are active. Only use this coding if the standard codings did not work. (codable in FRM)

Brightness of Angel Eyes 3 – alternative
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of Angel Eyes when low beams are active. Only use this coding if the standard codings did not work. (codable in FRM)

Daytime running lights – tail lights brightness
• off
• very low
• low
• medium
• high
• very high
Brightness for ‘Daytime running lights – tail lights’. (codable in FRM)

Daytime running lights
• standard
• permanently on
• permanently off
Set mode of daytime running lights. Set to ‘standard’ or ‘display menu’ to display a menu in the iDrive settings for changing the mode of daytime running lights. (codable in CIC)

Easy entry
• on
• off
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in CAS)

Easy entry Key 1
• on
• off
Separate setting for ‘Easy entry’ for key 1nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 2
• on
• off
Separate setting for ‘Easy entry’ for key 2nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 3
• on
• off
Separate setting for ‘Easy entry’ for key 3nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 4
• on
• off
Separate setting for ‘Easy entry’ for key 4nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Start/Stop-Automatic memory
• on
• off
Setting for Start/Stop-Automatic is saved. This way the manual setting of the Start/Stop-Automatic button, i.e. whether the button is turned on or off, is saved for the next start. Deactivating the Start/Stop-Automatic on the car can increase the life time of the battery and the starter. (codable in IHKA)

Flash to pass with bi-xenon
• on
• off
Bi-xenon lamps are used for flash to pass. (codable in FRM)

Front fog lights with flash to pass
• on
• off
Front fog lights are automatically turned off when activating flash to pass. (codable in FRM)

Gear shift indicator and suggestion 1/3
• on
• off
Gear shift indicator in the on board computer. To activate this function, also activate other codings for ‘Gear shift indicator’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Gear shift indicator and suggestion 2/3
• on
• off
Only change with ‘Gear shift indicator 1/2’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Gear shift indicator key 1
• on
• off
Gear shift indicator for key 1. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear shift indicator key 2
• on
• off
Gear shift indicator for key 2. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear shift indicator key 3
• on
• off
Gear shift indicator for key 3. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear shift indicator key 4
• on
• off
Gear shift indicator for key 4. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Head light cleaning
• on
• off
Turn head light cleaning on/off. (codable in JBBF)

Number until headlight cleaning
• 3
• 5
• 7
Head lights are cleaned every x-th time the windscreen washer has been activated. (codable in JBBF)

Number of splashes for head lights
• 2
• 3
Number of splashes for cleaning the head lights. (codable in JBBF)

Length of splash for head lights
• 0.7s
• 1s
• 0.5s
Length of a single splash for head light cleaning. (codable in JBBF)

Delay between splashes for head lights
• 1.3s
• 1s
• 1.5s
Delay between splashes for head light cleaning. (codable in JBBF)

Front fog lights with high beams
• on
• off
Front fog lights are automatically turned off when activating high beams. (codable in FRM)

Audible confirmation menu
• on
• off
Show menu for audible confirmation for locking/unlocking in iDrive. This coding only works when the DWA module is installed. (codable in CIC)

Address book menu
• on
• off
Show menu for address book in iDrive. (codable in CIC)

Notepad menu
• on
• off
Show menu for notepad in iDrive. (codable in CIC)

Audible confirmation
• on
• off
Enable menus for audible confirmation for locking/unlocking the vehicle in the iDrive. The menu can be found in the same menu as the other locking confirmation settings in the iDrive. Only works if an ‘Anti Theft Alarm System’ is installed, because the sound is generated by the siren of the anti theft alarm system and not by the horn. If you are not sure, whether an ‘Anti Theft Alarm System’ or only the standard ‘Anti Theft Protection’ is installed, please perform a diagnostic session. You can then check if the module for the anti theft alarm system was found or not. (codable in CCC)

Audible confirmation – unlocking vehicle
• on
• off
Display option for audible confirmation for unlocking the vehicle in the iDrive. Please enable ‘Audible confirmation’ for this as well in this module and carefully read the description for it. (codable in CCC)

Audible confirmation – locking vehicle 1/2
• on
• off
Display option for audible confirmation for locking the vehicle in the iDrive. Please enable ‘Audible confirmation’ for this as well in this module and carefully read the description for it. (codable in CCC)

Audible confirmation – locking vehicle 2/2
• on
• off
Only change this function with ‘Audible confirmation – locking vehicle 1/2’. (codable in CCC)

Rain light sensor sensitivity 1/2
• on
• off
Display menu for changing the sensitivity of the rain light sensor in the iDrive. The menu can be found in the same menu as the other light settings in the iDrive. (codable in CCC)

Rain light sensor sensitivity 2/2
• on
• off
Only change this function with ‘Rain light sensor sensitivity 1/2’. (codable in CCC)

Seat heater
• on
• off
Display menu for changing the heat distribution of the seat heater. The menu can be found in the same menu as the other heater settings in the iDrive. Also, changing the heating distribution often only works on 5 series with sport seats. (codable in CCC)

Cornering Light
• on
• off
Display menu for activating cornering light in the iDrive. The menu can be found in the same menu as the other light settings in the iDrive. Also, cornering light often requires adaptive headlights to be installed. (codable in CCC)

Digital speedometer
• on
• off
The current speed is shown in the digital display below the speedometer. (codable in KOMBI)

Digital speedometer correction
• true speed
• ‘corrected’ speed
Per default the speed shown in the digital speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)

‘Correction’ analog speedometer
• true speed
• ‘corrected’ speed
This coding does not work on US models. Per default the speed shown in the digital speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)

Blank information display in dashboard
• on
• off
Blank information display in dashboard is shown when you switch the information displays with the BC button. (codable in KOMBI)

GPS time correction
• on
• off
Time of day is corrected by using GPS. (codable in KOMBI)

Permanent speedometer lighting
• on
• off
Speedometer is always lit, even in the daytime. (codable in KOMBI)

Momentary fuel consumption
• on
• off
Show momentary fuel consumption in the on board computer. (codable in KOMBI)

Cruise Control speed display
• 0s
• 3s
• 6s
The set speed of the cruise control is shown for a couple of seconds in the on board computer. (codable in KOMBI)

Daytime running lights in OBC
• on
• off
Turn daytime running lights on/off in on board computer. Might not work if an iDrive system is installed. (codable in KOMBI)

Light sensitivity in OBC 1/2
• on
• off
Change light sensitivity in on board computer. Might not work if an iDrive system is installed. (codable in KOMBI)

Light sensitivity in OBC 2/2
• on
• off
Only change with ‘Light sensitivity in OBC 1/2’. (codable in KOMBI)

Gear shift indicator and suggestion 1/3
• on
• off
Gear shift indicator in the on board computer. To activate this function, also activate other codings for ‘Gear shift indicator’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Gear shift indicator and suggestion 2/3
• on
• off
Only change with ‘Gear shift indicator 1/2’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Gear shift indicator key 1
• on
• off
Gear shift indicator for key 1. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear shift indicator key 2
• on
• off
Gear shift indicator for key 2. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear shift indicator key 3
• on
• off
Gear shift indicator for key 3. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear shift indicator key 4
• on
• off
Gear shift indicator for key 4. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Interior lights with remote
• active
• off
Pressing the lock button on the remote, when the car is already locked, turns on the interior lights. (codable in CAS)

Interior lighting off after 2 minutes
• on
• off
Interior lighting is automatically turned off after two minutes. (codable in FRM)

Soft turn on/off for interior lighting
• on
• off
Interior lighting is softly turned on and off. (codable in FRM)

Save circulation settings
• on
• off
Circulation settings are saved for next start of the vehicle. (codable in IHKA)

Show ‘Auto’ in automatic mode
• on
• off
Auto’ is displayed in automatic mode for air conditioning. (codable in IHKA)

Blower level during automatic A/C
• on
• off
The current blower level is displayed even during automatic mode of the air conditioning. (codable in IHKA)

Blower symbol
• on
• off
Show blower symbol. (codable in IHKA)

Off-Mode Memory
• on
• off
Save setting for ‘Off-mode’ for the air conditioning. (codable in IHKA)

Compressor with A/C in ‘Auto’-mode 1/4
• on
• off
When pressing the ‘Automatic’ button for air conditioning, the air conditioning starts by itself. To deactivate this function, deactivate all functions for ‘Automatic compressor with A/C’. (codable in IHKA)

Compressor with A/C in ‘Auto’-mode 2/4
• on
• off
When pressing the ‘Automatic’ button for air conditioning, the air conditioning starts by itself. To deactivate this function, deactivate all functions for ‘Automatic compressor with A/C’. (codable in IHKA)

Compressor with A/C in ‘Auto’-mode 3/4
• on
• off
When pressing the ‘Automatic’ button for air conditioning, the air conditioning starts by itself. To deactivate this function, deactivate all functions for ‘Automatic compressor with A/C’. (codable in IHKA)

Compressor with A/C in ‘Auto’-mode 4/4
• on
• off
When pressing the ‘Automatic’ button for air conditioning, the air conditioning starts by itself. To deactivate this function, deactivate all functions for ‘Automatic compressor with A/C’. (codable in IHKA)

Residual heat with ‘ALL’-button
• on
• off
ALL’-button triggers residual heat function of the AC. (codable in IHKA)

Legal disclaimer (US)
• on
• off
Show legal disclaimer when iDrive is started. This warning is usually only shown in US-models. (codable in CIC)

Camera disclaimer
• on
• active (6 seconds)
• not active
Show legal disclaimer for rear view camera. (codable in CIC)

Night Vision disclaimer
• on
• active (6 seconds)
• not active
Show legal disclaimer for night vision view camera. (codable in CIC)

Legal disclaimer (US)
• on
• off
Show legal disclaimer when iDrive is started. This warning is usually only shown in US-models. (codable in CCC)

Legal disclaimer (US) – display time
• 0s
• 10s
Display time for the legal disclaimer in the iDrive. Setting this function to ‘0s’ deactivates the legal disclaimer and sometimes even speeds up the starting time of the iDrive. This warning is usually only shown in US-models. (codable in CCC)

Comfort close using remote
• on
• off
Press and hold the lock button on the remote to close all windows and the sunroof. (codable in CAS)

Comfort close using keylocks
• on
• off
Lock the car by key and hold the key in the lock position to close all windows and the sunroof. (codable in CAS)

Comfort close – door (comfort access)
• on
• off
Use comfort closing features when locking with the door handle. This only works if comfort access is installed. Touch the locking area on the door handle for a longer time to close all windows and the sunroof. (codable in CAS)

Comfort closing delay (mirrors)
• 0.0s
• 0.5s
• 1.5s
General delay for comfort closing. If ‘0.0s’ is set, mirrors fold immediately when car is locked. (codable in CAS)

Deactivate comfort access
• on
• off
In order to deactivate the comfort access, set this coding to ‘not active’. This coding cannot be used to activate a retrofitted comfort access. When the comfort access is deactivated, neither closing nor opening the car via the door handle will work. Turning the ignition and engine on/off without putting the key into the ignition (also known as ‘Keyless Go’) will also not work anymore. Therefore the car cannot be stolen anymore by tricking the comfort access. In order to activate comfort access again, please set this coding to ‘active’. (codable in CAS)

Lock tailgate when car locked
• on
• off
Tailgate cannot be unlocked, when car is locked. (codable in CAS)

Automatically lock vehicle duration
• 1 min
• 2 min
• 5 min
• 10 min
• 15 min
If no door or window has been opened after the car has been unlocked, the doors automatically lock. Use this function to set the duration after which the car is automatically locked. (codable in CAS)

Automatically lock vehicle Key 1
• on
• off
Separate setting for ‘Automatically lock vehicle’ for key 1nIf no door or window has been opened two minutes after the car has been unlocked, the doors automatically lock. (codable in CAS)

Automatically lock vehicle Key 2
• on
• off
Separate setting for ‘Automatically lock vehicle’ for key 2nIf no door or window has been opened two minutes after the car has been unlocked, the doors automatically lock. (codable in CAS)

Automatically lock vehicle Key 3
• on
• off
Separate setting for ‘Automatically lock vehicle’ for key 3nIf no door or window has been opened two minutes after the car has been unlocked, the doors automatically lock. (codable in CAS)

Automatically lock vehicle Key 4
• on
• off
Separate setting for ‘Automatically lock vehicle’ for key 4nIf no door or window has been opened two minutes after the car has been unlocked, the doors automatically lock. (codable in CAS)

Lock vehicle upon ignition
• on
• off
Vehicle is locked, when ignition is turned on. (codable in CAS)

Threshold speed for vehicle locking
• 2 kph / 1 mph
• 6 kph / 4 mph
• 12 kph / 8 mph
• 18 kph / 11 mph
• 24 kph / 15 mph
• 30 kph / 19 mph
Sets the speed at which the vehicle automatically locks all doors.nTo activate this function you need to activate ‘Lock vehicle at x kph’ for the according keys. (codable in CAS)

Lock vehicle at x kph Key 1
• on
• off
Automatically lock the vehicle at the set threshold speed when key 1 is used. (codable in CAS)

Lock vehicle at x kph Key 2
• on
• off
Automatically lock the vehicle at the set threshold speed when key 2 is used. (codable in CAS)

Lock vehicle at x kph Key 3
• on
• off
Automatically lock the vehicle at the set threshold speed when key 3 is used. (codable in CAS)

Lock vehicle at x kph Key 4
• on
• off
Automatically lock the vehicle at the set threshold speed when key 4 is used. (codable in CAS)

Optical confirmation – locking vehicle
• on
• off
Optical confirmation for locking vehicle is active/not active. (codable in FRM)

Optical confirmation lock vehicle Key 1
• on
• off
Optical confirmation for locking vehicle is active/not active. Separate setting for ‘Optical confirmation for locking’ for key 1. (codable in FRM)

Optical confirmation lock vehicle Key 2
• on
• off
Optical confirmation for locking vehicle is active/not active. Separate setting for ‘Optical confirmation for locking’ for key 2. (codable in FRM)

Optical confirmation lock vehicle Key 3
• on
• off
Optical confirmation for locking vehicle is active/not active. Separate setting for ‘Optical confirmation for locking’ for key 3. (codable in FRM)

Audible confirmation – locking vehicle
• on
• off
Audible confirmation for locking vehicle is active/not active. (codable in DWA)

Mirror tilt 1/2
• on
• off
Requirement for mirror tilt functions. (codable in FRM)

Mirror tilt 2/2
• on
• off
Requirement for mirror tilt functions. (codable in FRM)

Tilt mirror in reverse
• on
• off
This function requires an installed LIN-Bus (usually installed with mirror heating).nPassenger mirror is tilted when switching into reverse gear and the mirror switch is set to the driver side. To activate this function activate ‘Mirror tilt’ as well. (codable in FRM)

Comfort folding for sideview mirrors
• on
• off
This function requires an installed LIN-Bus (usually installed with mirror heating).nWhen holding the lock/unlock button on the remote the sideview mirrors automatically fold/unfold. May need additional coding of the ‘CAS’ module. (codable in FRM)

Electrochromatic mirror dimming
• on
• off
This function requires an installed LIN-Bus (usually installed with mirror heating). Side mirrors automatically dim electrochromatic. (codable in FRM)

Comfort open using remote
• on
• off
Press and hold the unlock button on the remote to open all windows and the sunroof. (codable in CAS)

Comfort open using keylocks
• on
• off
Unlock the car by key and hold the key in the unlock position to open all windows and the sunroof. (codable in CAS)

Deactivate comfort access
• on
• off
In order to deactivate the comfort access, set this coding to ‘not active’. This coding cannot be used to activate a retrofitted comfort access. When the comfort access is deactivated, neither closing nor opening the car via the door handle will work. Turning the ignition and engine on/off without putting the key into the ignition (also known as ‘Keyless Go’) will also not work anymore. Therefore the car cannot be stolen anymore by tricking the comfort access. In order to activate comfort access again, please set this coding to ‘active’. (codable in CAS)

Easy entry
• on
• off
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in CAS)

Easy entry Key 1
• on
• off
Separate setting for ‘Easy entry’ for key 1nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 2
• on
• off
Separate setting for ‘Easy entry’ for key 2nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 3
• on
• off
Separate setting for ‘Easy entry’ for key 3nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 4
• on
• off
Separate setting for ‘Easy entry’ for key 4nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Selective central locking
• on
• off
Unlocking the car once only unlocks the driver’s door. Unlocking it again unlocks the other doors, too. (codable in CAS)

Selective central locking Key 1
• on
• off
Separate setting for ‘Selective central locking’ for key 1nUnlocking the car once only unlocks the driver’s door. Unlocking it again unlocks the other doors, too. (codable in CAS)

Selective central locking Key 2
• on
• off
Separate setting for ‘Selective central locking’ for key 2nUnlocking the car once only unlocks the driver’s door. Unlocking it again unlocks the other doors, too. (codable in CAS)

Selective central locking Key 3
• on
• off
Separate setting for ‘Selective central locking’ for key 3nUnlocking the car once only unlocks the driver’s door. Unlocking it again unlocks the other doors, too. (codable in CAS)

Selective central locking Key 4
• on
• off
Separate setting for ‘Selective central locking’ for key 4nUnlocking the car once only unlocks the driver’s door. Unlocking it again unlocks the other doors, too. (codable in CAS)

Selective central locking – unlock fuel lid
• on
• off
The fuel lid is also unlocked upon the first unlock, when ‘Selective central locking’ is active. (codable in CAS)

Unlock car when turned off
• on
• off
Doors are automatically unlocked, when ignition key is ejected. Only works if ‘Lock vehicle at x kph Key 1-4’ is activated. (codable in CAS)

Optical confirmation – unlocking vehicle
• on
• off
Optical confirmation for unlocking vehicle is active/not active. (codable in FRM)

Optical confirmation unlock vehicle Key 1
• on
• off
Optical confirmation for unlocking vehicle is active/not active. Separate setting for ‘Optical confirmation for unlocking’ for key 1. (codable in FRM)

Optical confirmation unlock vehicle Key 2
• on
• off
Optical confirmation for unlocking vehicle is active/not active. Separate setting for ‘Optical confirmation for unlocking’ for key 2. (codable in FRM)

Optical confirmation unlock vehicle Key 3
• on
• off
Optical confirmation for unlocking vehicle is active/not active. Separate setting for ‘Optical confirmation for unlocking’ for key 3. (codable in FRM)

Audible confirmation – unlocking vehicle
• on
• off
Audible confirmation for unlocking vehicle is active/not active. (codable in DWA)

PDC view
• vertical (F-Models)
• horizontal (E-Models)
Direction of park distance control view. (codable in CIC)

Comfort standing light
• on
• off
If the light switch is set at automatic or on, the parking lights remain on, until the vehicle is locked with the remote. (codable in FRM)

Power windows after ignition off
• on
• off
Power windows are active for another minute after ignition is turned off. (codable in CAS)

Power windows after ignition off
• 1 min
• 2 min
• 5 min
• 10 min
• 15 min
Duration in minutes, for which power windows are active after turning off the ignition. (codable in CAS)

Easy entry
• on
• off
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in CAS)

Easy entry Key 1
• on
• off
Separate setting for ‘Easy entry’ for key 1nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 2
• on
• off
Separate setting for ‘Easy entry’ for key 2nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 3
• on
• off
Separate setting for ‘Easy entry’ for key 3nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Easy entry Key 4
• on
• off
Separate setting for ‘Easy entry’ for key 4nPress the unlock button once to unlock all doors. Press it again to lower the driver side window. (codable in CAS)

Continue window action when door is opened
• on
• off
When the door is opened while its window is opening/closing, the window will continue opening/closing the window. (codable in FRM)

Continue window action when engine started
• on
• off
When the engine is started while a window is opening/closing, the window will continue opening/closing the window. (codable in FRM)

Rain light sensor sensitivity 1/2
• on
• off
Display menu for changing the sensitivity of the rain light sensor in the iDrive. The menu can be found in the same menu as the other light settings in the iDrive. (codable in CCC)

Rain light sensor sensitivity 2/2
• on
• off
Only change this function with ‘Rain light sensor sensitivity 1/2’. (codable in CCC)

Seatbelt Hand-Over
• on
• off
Automatic seatbelt hand-over is active/inactive. (codable in FRM)

Seatbelt Hand-Over driver
• on
• off
Automatic seatbelt hand-over for driver is active/inactive. (codable in FRM)

Seatbelt Hand-Over passenger
• on
• off
Automatic seatbelt hand-over for passenger is active/inactive. (codable in FRM)

Seat heater
• on
• off
Display menu for changing the heat distribution of the seat heater. The menu can be found in the same menu as the other heater settings in the iDrive. Also, changing the heating distribution often only works on 5 series with sport seats. (codable in CCC)

Seat heater level in menu
• on
• off
Show the current seat heater level for the front seats in the seat heater menu. (codable in CCC)

Show seat heater menu automatically
• on
• off
Show seat heater menu for a few seconds when activating the seat heater. This function often only works in 5 series models. (codable in CCC)

Sidemarker (US)
• on
• off
Sidemarkers are permanently active. May need additional ‘Sidemarker (US)’ functions set to ‘active’ if available. If warnings for the turn signals are shown after successfully coding this, please disable the voltage monitoring for the turn signals. This warning is most likely due to the fact that your car is not a US model. (codable in FRM)

Sidemarker (US) brightness
• off
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness for ‘Sidemarker (US)’. (codable in FRM)

Digital speedometer
• on
• off
The current speed is shown in the digital display below the speedometer. (codable in KOMBI)

Digital speedometer correction
• true speed
• ‘corrected’ speed
Per default the speed shown in the digital speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)

‘Correction’ analog speedometer
• true speed
• ‘corrected’ speed
This coding does not work on US models. Per default the speed shown in the digital speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)

Unlock rear window
• on
• off
Key unlocks rear window instead of trunk lid in touring models. (codable in CAS)

Unlock rear window key 1
• on
• off
Key 1 unlocks rear window instead of trunk lid in touring models. (codable in CAS)

Unlock rear window key 2
• on
• off
Key 2 unlocks rear window instead of trunk lid in touring models. (codable in CAS)

Unlock rear window key 3
• on
• off
Key 3 unlocks rear window instead of trunk lid in touring models. (codable in CAS)

Unlock rear window key 4
• on
• off
Key 4 unlocks rear window instead of trunk lid in touring models. (codable in CAS)

Unlock rear window via outside button
• on
• off
Outside trunk lid button opens rear window instead of trunk lid in touring models. (codable in CAS)

Unlock rear window via outside button Key 1
• on
• off
Outside trunk lid button opens rear window instead of trunk lid in touring models. Separate setting for key 1. (codable in CAS)

Unlock rear window via outside button Key 2
• on
• off
Outside trunk lid button opens rear window instead of trunk lid in touring models. Separate setting for key 2. (codable in CAS)

Unlock rear window via outside button Key 3
• on
• off
Outside trunk lid button opens rear window instead of trunk lid in touring models. Separate setting for key 3. (codable in CAS)

Unlock rear window via outside button Key 4
• on
• off
Outside trunk lid button opens rear window instead of trunk lid in touring models. Separate setting for key 4. (codable in CAS)

Unlock rear window with footwell switch
• on
• off
Footwell switch opens rear window instead of trunk lid in touring models. (codable in CAS)

Open rear window via footwell switch Key 1
• on
• off
Footwell switch opens rear window instead of trunk lid in touring models. Separate setting for key 1. (codable in CAS)

Open rear window via footwell switch Key 2
• on
• off
Footwell switch opens rear window instead of trunk lid in touring models. Separate setting for key 2. (codable in CAS)

Open rear window via footwell switch Key 3
• on
• off
Footwell switch opens rear window instead of trunk lid in touring models. Separate setting for key 3. (codable in CAS)

Open rear window via footwell switch Key 4
• on
• off
Footwell switch opens rear window instead of trunk lid in touring models. Separate setting for key 4. (codable in CAS)

Threshold for low range warning
• off
• 20 km / 12 mi
• 50 km / 31 mi
Threshold for acoustic low range warning due to low fuel level. (codable in KOMBI)

Threshold for tank reserve warning
• 6.5 litres
• 8.0 litres
• 10.0 litres
• 12.5 litres
• 20.0 litres
Threshold for tank reserve warning due to low fuel level. (codable in KOMBI)

Telephone ringtone
• BMW
• Mini
Customize telephone ringtone. (codable in CIC)

Hazard lights
• standard
• double
Hazard lights blink once or twice. (codable in FRM)

Crash lights
• standard
• double
Hazard lights blink once or twice upon an accident. (codable in FRM)

One-touch turn signal function
• 1
• 3
• 5
Number of turn signals when tapping the turn signal. If available, please activate this option for the different keys as well. In some cases, this option also needs to be enabled in the iDrive. (codable in FRM)

One-touch turn signal function Key 1
• 1
• 3
• 5
Number of turn signals when tapping the turn signal. Separate setting for ‘One-touch turn signal function’ for key 1. (codable in FRM)

One-touch turn signal function Key 2
• 1
• 3
• 5
Number of turn signals when tapping the turn signal. Separate setting for ‘One-touch turn signal function’ for key 2. (codable in FRM)

One-touch turn signal function Key 3
• 1
• 3
• 5
Number of turn signals when tapping the turn signal. Separate setting for ‘One-touch turn signal function’ for key 3. (codable in FRM)

Turn signals front as LED
• on
• off
Activate this option if you have replaced the turn signals front with LED bulbs. (codable in FRM)

Turn signals rear as LED
• on
• off
Activate this option if you have replaced the turn signals rear with LED bulbs. (codable in FRM)

Optical confirmation – unlocking vehicle
• on
• off
Optical confirmation for unlocking vehicle is active/not active. (codable in FRM)

Optical confirmation unlock vehicle Key 1
• on
• off
Optical confirmation for unlocking vehicle is active/not active. Separate setting for ‘Optical confirmation for unlocking’ for key 1. (codable in FRM)

Optical confirmation unlock vehicle Key 2
• on
• off
Optical confirmation for unlocking vehicle is active/not active. Separate setting for ‘Optical confirmation for unlocking’ for key 2. (codable in FRM)

Optical confirmation unlock vehicle Key 3
• on
• off
Optical confirmation for unlocking vehicle is active/not active. Separate setting for ‘Optical confirmation for unlocking’ for key 3. (codable in FRM)

Optical confirmation – locking vehicle
• on
• off
Optical confirmation for locking vehicle is active/not active. (codable in FRM)

Optical confirmation lock vehicle Key 1
• on
• off
Optical confirmation for locking vehicle is active/not active. Separate setting for ‘Optical confirmation for locking’ for key 1. (codable in FRM)

Optical confirmation lock vehicle Key 2
• on
• off
Optical confirmation for locking vehicle is active/not active. Separate setting for ‘Optical confirmation for locking’ for key 2. (codable in FRM)

Optical confirmation lock vehicle Key 3
• on
• off
Optical confirmation for locking vehicle is active/not active. Separate setting for ‘Optical confirmation for locking’ for key 3. (codable in FRM)

Video in motion 1/2
• on
• off
Enable video and DVD while driving. This is only possible if the car supports watching TV or playing DVDs while standing. In order to enable this option, activate ‘Video in motion 2/2’ as well. (codable in CIC)

Video in motion 2/2
• on
• off
Only change this function with ‘Video in motion 1/2’. This is only possible if the car supports watching TV or playing DVDs while standing. (codable in CIC)

Video in motion
• during driving
• only walking pace
• only when handbrake pulled
• not active
Enable video and DVD while driving. This is only possible if the car supports watching TV or playing DVDs while standing. (codable in CCC)

Angel Eyes voltage monit. 1/2
• on
• off
Voltage monitoring for angel eyes. Might cause flickering of LED lights. (codable in FRM)

Angel Eyes voltage monit. 2/2
• on
• off
Deactivate with ‘Angel Eyes voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Sidemarker voltage monit. 1/2
• on
• off
Voltage monitoring for sidemarkers. Might cause flickering of LED lights. (codable in FRM)

Sidemarker voltage monit. 2/2
• on
• off
Deactivate with ‘Sidemarker voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Turn signals front voltage monit. 1/2
• on
• off
Voltage monitoring for turn signals front. Might cause flickering of LED lights. (codable in FRM)

Turn signals front voltage monit. 2/2
• on
• off
Deactivate with ‘Turn signals front voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Fog lights voltage monit. 1/2
• on
• off
Voltage monitoring for fog lights. Might cause flickering of LED lights. (codable in FRM)

Fog lights voltage monit. 2/2
• on
• off
Deactivate with ‘Fog lights voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

High beams voltage monit. 1/2
• on
• off
Voltage monitoring for high beams. Might cause flickering of LED lights. (codable in FRM)

High beams voltage monit. 2/2
• on
• off
Deactivate with ‘High beams voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Low beams voltage monit. 1/2
• on
• off
Voltage monitoring for low beams. Might cause flickering of LED lights. (codable in FRM)

Low beams voltage monit. 2/2
• on
• off
Deactivate with ‘Low beams voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Turn signals rear voltage monit. 1/2
• on
• off
Voltage monitoring for turn signals rear. Might cause flickering of LED lights. (codable in FRM)

Turn signals rear voltage monit. 2/2
• on
• off
Deactivate with ‘Turn signals rear voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Braking lights voltage monit. 1/2
• on
• off
Voltage monitoring for braking lights. Might cause flickering of LED lights. (codable in FRM)

Braking lights voltage monit. 2/2
• on
• off
Deactivate with ‘Braking lights voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Inner brake light voltage monit. 1/2
• on
• off
Voltage monitoring for inner brake light. Might cause flickering of LED lights. (codable in FRM)

Inner brake light voltage monit. 2/2
• on
• off
Deactivate with ‘Inner brake light voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Third brake light voltage monit. 1/2
• on
• off
Voltage monitoring for third brake light. Might cause flickering of LED lights. (codable in FRM)

Third brake light voltage monit. 2/2
• on
• off
Deactivate with ‘Third brake light voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Tail lights voltage monit. 1/2
• on
• off
Voltage monitoring for tail lights. Might cause flickering of LED lights. (codable in FRM)

Tail lights voltage monit. 2/2
• on
• off
Deactivate with ‘Tail lights voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Reversing lights voltage monit. 1/2
• on
• off
Voltage monitoring for reversing lights. Might cause flickering of LED lights. (codable in FRM)

Reversing lights voltage monit. 2/2
• on
• off
Deactivate with ‘Reversing lights voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

License plate lighting voltage monit. 1/2
• on
• off
Voltage monitoring for license plate lighting. Might cause flickering of LED lights. (codable in FRM)

License plate lighting voltage monit. 2/2
• on
• off
Deactivate with ‘License plate lighting voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Rear fog lights voltage monit. 1/2
• on
• off
Voltage monitoring for rear fog lights. Might cause flickering of LED lights. (codable in FRM)

Rear fog lights voltage monit. 2/2
• on
• off
Deactivate with ‘Rear fog lights voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Rear fog light left voltage monit. 1/2
• on
• off
Voltage monitoring for rear left fog light. Might cause flickering of LED lights. (codable in FRM)

Rear fog light left voltage monit. 2/2
• on
• off
Deactivate with ‘Rear fog light left voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Rear fog light right voltage monit. 1/2
• on
• off
Voltage monitoring for rear right fog light. Might cause flickering of LED lights. (codable in FRM)

Rear fog light right voltage monit. 2/2
• on
• off
Deactivate with ‘Rear fog light right voltage monit. 1/2’ to disable flickering of LED lights. (codable in FRM)

Speed limit warning
• off
• 120 kph / 75 mph
• 190 kph / 120 mph
• 210 kph / 130 mph
• 240 kph / 150 mph
Speed limit warning at 120 kph is active/not active. (codable in KOMBI)

Temperature warning
• on
• off
Warning for outside temperature below 4° C / 39° F is active/not active. (codable in KOMBI)

Ignition key warning
• on
• off
Ignition key warning active/not active. (codable in KOMBI)

Threshold for low range warning
• off
• 20 km / 12 mi
• 50 km / 31 mi
Threshold for acoustic low range warning due to low fuel level. (codable in KOMBI)

Threshold for tank reserve warning
• 6.5 litres
• 8.0 litres
• 10.0 litres
• 12.5 litres
• 20.0 litres
Threshold for tank reserve warning due to low fuel level. (codable in KOMBI)

Lights-on warning
• on
• off
A warning is shown, when the driver’s door is opened while the lights are still on. (codable in FRM)

Angel Eyes/standing lights warning
• on
• off
Warning for malfunction of angel eyes and the front standing lights in the on board computer. (codable in FRM)

Turn signals front warning
• on
• off
Warning for malfunction of front turn signals in the on board computer. (codable in FRM)

Fog lights front warning
• on
• off
Warning for malfunction of front fog lights in the on board computer. (codable in FRM)

High beams warning
• on
• off
Warning for malfunction of high beams in the on board computer. (codable in FRM)

Low beams warning
• on
• off
Warning for malfunction of low beams in the on board computer. (codable in FRM)

Turn signals rear warning
• on
• off
Warning for malfunction of rear turn signals in the on board computer. (codable in FRM)

Outer brake lights warning
• on
• off
Warning for malfunction of outer braking lights in the on board computer. (codable in FRM)

Inner brake lights warning
• on
• off
Warning for malfunction of inner braking lights in the on board computer. (codable in FRM)

Third brake light warning
• on
• off
Warning for malfunction of third brake light in the on board computer. (codable in FRM)

Tail lights warning
• on
• off
Warning for malfunction of tail lights in the on board computer. (codable in FRM)

Reversing lights warning
• on
• off
Warning for malfunction of reversing lights in the on board computer. (codable in FRM)

License plate light warning
• on
• off
Warning for malfunction of license plate lights in the on board computer. (codable in FRM)

Rear fog light left warning
• on
• off
Warning for malfunction of rear left fog light in the on board computer. (codable in FRM)

Rear fog light right warning
• on
• off
Warning for malfunction of rear right fog light in the on board computer. (codable in FRM)

Seat belt warning
• off
• on
Various settings for the seat belt warning. (codable in CSM)

Seat belt reminder driver
• off
• on
Seat belt reminder for driver is active/ inactive. (codable in CSM)

Seat belt reminder passenger
• off
• on
Seat belt reminder for passenger is active/ inactive. (codable in CSM)

Welcome lights
• on
• off
Welcome lights are turned on, when vehicle is unlocked. In order for the welcome light to work, the light switch in the car has to be set to ‘Auto’. In some cases, this option also needs to be enabled in the iDrive. In order to customize which lights should be turned on, please use the following options. (codable in FRM)

Welcome lights Key 1
• on
• off
Separate setting for ‘Welcome lights’ for key 1. (codable in FRM)

Welcome lights Key 2
• on
• off
Separate setting for ‘Welcome lights’ for key 2. (codable in FRM)

Welcome lights Key 3
• on
• off
Separate setting for ‘Welcome lights’ for key 3. (codable in FRM)

Welcome lights Key 4
• on
• off
Separate setting for ‘Welcome lights’ for key 4. (codable in FRM)

Welcome lights duration
• off
• 5s
• 10s
• 20s
• 40s
• 90s
• 150s
• 240s
Duration of the welcome lights in seconds. (codable in FRM)

Welcome lights – low beams
• off
• turn on softly
• turn on hard
Low beams are turned on with welcome lights. (codable in FRM)

Welcome lights – brake force display
• off
• turn on softly
• turn on hard
Brake force display is turned on with welcome lights. (codable in FRM)

Welcome lights – braking lights
• off
• turn on softly
• turn on hard
Braking lights are turned on with welcome lights. (codable in FRM)

Welcome lights – turn signals front
• off
• turn on softly
• turn on hard
Turn signals front are turned on with welcome lights. To activate this function you may need to additionally code ‘Sidemarker (US) brightness’ to ‘very low’ or higher. (codable in FRM)

Welcome lights – turn signals rear
• off
• turn on softly
• turn on hard
Turn signals rear are turned on with welcome lights. To activate this function you may need to additionally code ‘Sidemarker (US) brightness’ to ‘very low’ or higher. (codable in FRM)

Welcome lights – high beams
• off
• turn on softly
• turn on hard
High beams are turned on with welcome lights. (codable in FRM)

Welcome lights – number plate lighting
• off
• turn on softly
• turn on hard
Number plate lights are turned on with welcome lights. (codable in FRM)

Welcome lights – front fog lights
• off
• turn on softly
• turn on hard
Front fog lights are turned on with welcome lights. (codable in FRM)

Welcome lights – rear fog lights
• off
• turn on softly
• turn on hard
Rear fog lights are turned on with welcome lights. (codable in FRM)

Welcome lights – corner LEDs
• off
• turn on softly
• turn on hard
Corner LEDs are turned on with welcome lights. Due to the way LEDs work, it is not possible to softly turn them on. (codable in FRM)

Welcome lights – standing lights front
• off
• turn on softly
• turn on hard
Standing lights front are turned on with welcome lights. (codable in FRM)

Welcome lights – standing lights rear
• off
• turn on softly
• turn on hard
Standing lights rear are turned on with welcome lights. (codable in FRM)

Active Sound Design Mode
• off
• M5/M6
Mode for Active Sound Design. The Active Sound Design module produces an amplified exhaust sound in the interior through the speakers. If you disable this function a fault code in the ASD might appear. To remove this fault code restore the ASD from ist original backup, since the fault code appeared because the ASD has been disabled. (codable in ASD)

Active Sound Design Volume
• very quiet
• quiet
• medium
• loud
• very loud
Volume for active sound design. (codable in ASD)

Audible confirmation menu
• on
• off
Show menu for audible confirmation for locking/unlocking in iDrive. This coding only works when the FZD module is installed. (codable in CIC)

Audible confirmation after complete closing
• on
• off
Audible confirmation for locking vehicle is active/not active. Confirmation will occur after every door and the tailgate are closed. (codable in FZD)

Audible confirmation at night
• on
• off
Between 8:00 PM and 8:00 AM the volume of the sound for the audible confirmation for locking/unlocking the vehicle is automatically turned lower. (codable in FZD)

Optical confirmation after complete closing
• on
• off
Optical confirmation for locking vehicle is active/not active. Confirmation will occur after every door and the tailgate are closed. (codable in FZD)

Optical confirmation – tail gate
• on
• off
When the trunk/tail gate is closed while the car is locked the turn signals blink. This coding only works if Comfort Access is installed in the car. (codable in FZD)

Alarm type
• Europe
• USA
• UK
Type and sound of the alarm. United Kingdom is the same sound as Europe, the duration of the alarm is eight times longer. (codable in FZD)

Audible confirmation – length
• very short
• short
• medium
• long
• very long
Length of audible confirmation chirp. (codable in FZD)

Audible confirmation – pitch
• very low
• low
• medium
• high
• very high
Pitch for audible confirmation. (codable in FZD)

Audible confirmation – min. volume
• 7%
• 13%
• 20%
• 27%
• 33%
• 40%
• 47%
• 53%
• 60%
• 67%
• 73%
• 80%
• 87%
• 93%
• 100%
Minimum volume for the audible confirmation chirp. (codable in FZD)

Audible confirmation – max. volume
• 7%
• 13%
• 20%
• 27%
• 33%
• 40%
• 47%
• 53%
• 60%
• 67%
• 73%
• 80%
• 87%
• 93%
• 100%
Maximum volume for the audible confirmation chirp. (codable in FZD)

Alarm with sound
• on
• off
Use this function to turn the alarm sound completely off. When an alarm is triggered only the lights will flash. This also disables the audible confirmation when locking the vehicle. (codable in FZD)

Alarm at night
• on
• off
Between 8:00 PM and 8:00 AM the alarm is automatically turned off. In this time the audible confirmation for locking/unlocking the vehicle is also turned off. (codable in FZD)

Alarm with turn signals
• on
• off
Turn signals blink when alarm is initiated. (codable in FZD)

Alarm with dimmed headlights
• on
• off
Dimmed headlights blink when alarm is initiated. (codable in FZD)

Alarm with high beams
• on
• off
High beams blink when alarm is initiated. (codable in FZD)

Audible confirmation – unlocking vehicle
• on
• off
Audible confirmation for unlocking vehicle is active/not active. (codable in FZD)

Audible confirmation – locking vehicle
• on
• off
Audible confirmation for locking vehicle is active/not active. (codable in FZD)

Ambient lighting brightness 1/2
• same brightness as speedometer
• own brightness
Usually the brightness of the ambient lighting is automatically adjusted to the brightness of the speedometer illumination. To set the brightness indepently from the speedometer illumination, set this function to ‘own brightness’. The brightness of the ambient lighting can then be changed with ‘Ambient lighting brightness 2/2’. (codable in BDC)

Ambient lighting brightness 2/2
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Own brightness for ambient lighting. In order to activate this function, set ‘Ambient lighting brightness’ to ‘own brightness’. (codable in BDC)

Individual ambient light
• on
• off
Show menu in iDrive to individualize ambient light. Functions depend on the installed lights. (codable in NBT)

iDrive off when open door
• on
• off
Radio and Navigation turn off when the driver door is opened. This function doesn’t have an effect while engine is running. (codable in BDC)

Maximum volume when ignition on
• quiet
• medium
• loud
Maximum volume for radio/music when the vehicle is turned on. The volume of the last drive is used. (codable in CIC)

Warning and menu sounds
• BMW
• Mini
• BMW i
• Rolls Royce
Depending on the manufacturer of the vehicle (BMW, Mini, BMW i or Rolls Royce) different sounds are used for warnings and menus. Use this feature to change the sounds to a different brand, for example from ‘BMW’ to ‘Rolly Royce’. (codable in NBT)

Audio source iPhone 1/2
• on
• on (alternative)
• off
If an iPhone is connected via USB (either in the glove box or in the center console) it can be used as an audio source. (codable in NBT)

Audio source iPhone 2/2
• on
• on (alternative)
• off
Only change this function with ‘Tire pressure menu in iDrive 1/3’. (codable in NBT)

Brake force display
• off
• more lights
• flashing brake signals
When braking hard (ABS needs to be triggered) the brake lights either flash or additional lights are turned on to signal the car behind that an emergency brake has been carried out. (codable in BDC)

Brake force display – lights
• rear turn signals
• brake lights
• third braking light
Lights to be used for brake force display. (codable in BDC)

Brake force display – minimum speed
• 5 kph / 3 mph
• 10 kph / 6 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
Minimum speed threshold for brake force display. In order to enable this option, activate ‘Brake force display’ as well. (codable in BDC)

Start engine without brake 1/2
• on
• off
To start engine without brake turn on ignition first and press ‘Start Stop’ long. Only change with ‘Start engine without brake 2/2’. (codable in BDC)

Start engine without brake 2/2
• on
• off
Only change with ‘Start engine without brake 1/2’. (codable in BDC)

Threshold washer fluid warning
• low
• medium
• high
Threshold at which the washer fluid warning is turned on. The higher the threshold to activate this warning, the sooner this warning will be shown. (codable in BDC)

Number of wipes after windscreen cleaning
• 1
• 2
• 3
• 4
Number of wipes after windscreen is cleaned. (codable in BDC)

Number of wipes after rear window cleaning
• off
• 1
• 2
• 3
• 4
Number of wipes after rear window is cleaned. (codable in BDC)

Wiping interval rear window
• off
• 2s
• 4s
• 6s
• 8s
• 10s
• 12s
• 15s
Interval in seconds for windscreen rear window wipers. (codable in BDC)

Reduce wiper speed
• off
• 130 kph / 80 mph
• 170 kph / 105 mph
• 210 kph / 130 mph
Threshold at which the wiper speed is reduced. (codable in BDC)

Rear window cleaning with low washer liquid
• on
• off
Rear windows are also cleaned even though the washer fluid level is low. (codable in BDC)

Wipe delay after windowscreen cleaning
• 0.1 s
• 0.3 s
• 0.5 s
• 0.7 s
Windscreen wipers wipe 0.x seconds after windscreen is cleaned. (codable in BDC)

Wipe delay after rear window cleaning
• 0.1 s
• 0.3 s
• 0.5 s
• 0.7 s
• 0.9 s
• 1.1 s
• 1.3 s
• 1.5 s
Rear window wipers wipe 0.x seconds after rear window is cleaned. (codable in BDC)

Wiping interval standstill
• 3s
• 5s
Interval in seconds for windscreen wipers at standstill. (codable in BDC)

Windscreen wipers continue
• on
• off
Windscreen wipers don’t stop in the middle of the windscreen when ignition is turned off. Instead they complete their wiping cycle. (codable in BDC)

Number until headlight cleaning
• 1
• 5
• 10
• 15
Head lights are cleaned every x-th time the windscreen washer has been activated. (codable in BDC)

Continue rear wiper when igntion turned on
• on
• off
Rear wiper continue wiping and don’t interrupt, when the ignition is turned on. (codable in BDC)

Rear wiper permanent when reversing
• on
• off
When rear wipers are active while reversing, they are automatically set to permament wiping. (codable in BDC)

Head light cleaning
• on
• off
Turn head light cleaning on/off. (codable in BDC)

Maximum speed headlight cleaning
• 6 kph / 4 mph
• 12 kph / 8 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
• 80 kph / 50 mph
• 130 kph / 80 mph
Maximum speed at which folding headlight cleaning is possible. (codable in BDC)

Number of splashes for head lights
• 1
• 2
• 3
Number of splashes for cleaning the head lights. (codable in BDC)

Length of splash for head lights
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Length of a single splash for head light cleaning. (codable in BDC)

Delay between splashes for head lights
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Delay between splashes for head light cleaning. (codable in BDC)

Cleanings until 1st headlight cleaning
• off
• 1
• 3
• 5
• 8
• 10
• 15
Head lights are cleaned for the first time after the x-th time the windscreen washer has been activated. (codable in BDC)

GPS time correction
• on
• off
Time of day is corrected by using GPS. (codable in KOMBI)

Date incl. Time in dashboard
• on
• off
Show date including current time in the dashboard. In order to activate this function, please also activate ‘Date in dashboard’. (codable in KOMBI)

Start engine without brake 1/2
• on
• off
To start engine without brake turn on ignition first and press ‘Start Stop’ long. Only change with ‘Start engine without brake 2/2’. (codable in BDC)

Start engine without brake 2/2
• on
• off
Only change with ‘Start engine without brake 1/2’. (codable in BDC)

Start engine without clutch
• on
• off
To start engine without clutch turn on ignition first and press ‘Start Stop’ long. Please mind the selected gear at start. Only for manual transmission. (codable in BDC)

Comfort open sunroof immediately
• on
• off
Start opening the sunroof immediately during comfort opening. (codable in BDC)

Comfort close sunroof immediately
• on
• off
Start closing the sunroof immediately during comfort closing. (codable in BDC)

Comfort open windows simultaneously
• on
• off
Front and back windows open simultaneously during comfort opening. (codable in BDC)

Comfort close windows simultaneously
• on
• off
Front and back windows close simultaneously during comfort closing. (codable in BDC)

Comfort open using remote
• on
• off
Press and hold the unlock button on the remote to open all windows and the sunroof. (codable in BDC)

Comfort close using remote
• on
• off
Press and hold the lock button on the remote to close all windows and the sunroof. (codable in BDC)

Comfort close – door (comfort access)
• on
• off
Use comfort closing features when locking with the door handle. This only works if comfort access is installed. Touch the locking area on the door handle for a longer time to close all windows and the sunroof. (codable in BDC)

Comfort open delay
• 0.0 s
• 0.5 s
• 1.5 s
• 2.5 s
General delay for comfort opening. If ‘0.0s’ is set, comfort opening is immediately started when the car is unlocked. (codable in BDC)

Comfort closing delay (mirrors)
• 0.0s
• 0.5s
• 1.5s
General delay for comfort closing. If ‘0.0s’ is set, mirrors fold immediately when car is locked. (codable in BDC)

Door lock after driving away
• on
• off
Show menu in iDrive to activate door lock after driving away in vehicle settings ‘Doors/Key’. (codable in NBT)

Extend follow me home lights
• on
• off
Follow me home lights are displayed longer, when activating the flash to pass again. (codable in BDC)

Daytime running lights – light switch
• off
• A or 0
• A, 0 or 1
Positions for the light switch where the daytime running lights function is activated. (codable in BDC)

Daytime running lights
• display menu
• permanently on
• permanently off
Set mode of daytime running lights. Set to ‘display menu’ to display a menu in the iDrive settings for changing the mode of daytime running lights. (codable in CIC)

Color of Navigation Graphics
• orange
• HUD orange, Instruments gray
Use this function to change the color of navigation graphics in cluster (Head-Up and instrument cluster display). (codable in KOMBI)

HUD Startup time
• off
• very short
• short
• medium
• long
• very long
Time for start logo screen when Head-Up display is turned on. (codable in KOMBI)

Lane change in Head-Up Display
• on
• off
Use this function to show lane change warning in the head up display. (codable in KOMBI)

Display compass
• on
• off
Show the compass in board computer (OBC). Select compass by pushing the ‘BC’ button on the left side of the indicator arm. (codable in KOMBI)

Digital Speed Display
• off
• kmh
• kmh (Option 2)
• mph
• mph (Option 2)
Use this function to display digital speed in instrument cluster. Digital speedometer setting must be enabled in iDrive display settings. (codable in KOMBI)

Display ‘Diesel’ next to fuel level
• on
• off
Use this function to show the diesel sign next to fuel level indicator in the Kombi display. Not available in sports mode. (codable in KOMBI)

Display engine power
• on
• off
Use this function to show horsepowers in the instrument cluster below the rev counter. This display is only active in sports mode. (codable in KOMBI)

Display Layout Kombi
• BMW AG
• M GmbH
• Alpina Tuning
Use this function to change the layout of your Kombi display. When select ‘Alpina’ please also enable ‘Display Layout Kombi – Alpina’ aktiviert werden. (codable in KOMBI)

Display Layout Kombi – Alpina
• on
• off
Only change this coding in combination with ‘Display Layout Kombi’ when ‘Alpina’ is selected. When coding is active for some models the fuel level may not be calculated correctly. This is because Alpina models normally have larger fuel tanks than 60 liters. Therefore, please check the fuel indicator after coding this function. (codable in KOMBI)

Logo KOMBI
• no logo
• edrive
• M-Sport
• m550i
• m550d
• m40d
• m760i
• m760il
• B7 Biturbo
• B7
• B6 Biturbo
• B6
• B5 Biturbo
• D5 Biturbo
• XD3 Biturbo
• m750ld
• m750d
• V12
Use this function so change the logo inside KOMBI display. Not available in M view. (codable in KOMBI)

ECO PRO layout change
• on
• off
Show menu in iDrive to activate/deactivate the layout change of the instrument cluster when changing to ECO Pro mode. (codable in NBT)

Instant fuel consumption
• on
• off
Activate an iDrive menu to show the instant fuel consumption display in the instrument cluster. (codable in NBT)

Drive mode warning
• on
• off
Show menu in iDrive to activate/deactivate the warning message after chaging the drive mode. (codable in NBT)

Speedometer Zoom
• on
• off
Show menu in iDrive to activate highlighting the current speed in the speedometer. (codable in NBT)

X View menu
• on
• off
Show ‘X View’ menu in the iDrive. In this menu you can check the current pitch and roll of your vehicle. This option is only available for vehicles with all-wheel-drive. (codable in NBT)

Automatic clock change 1/2
• on
• off
When daylight savings time is active/not active, automatically update the time. Only change with ‘Automatic time setting 2/2’. (codable in NBT)

Bang Olufsen sound menu
• on
• on (alternative)
• off
Show Bang and Olufsen menu in iDrive. Use this menu to access special Bang and Olufsen equalizer settings. Some functions depend on the installed speakers. (codable in NBT)

M-driving dynamics
• on
• off
Show menu in iDrive inside instrument cluster settings to activate M-driving dynamics. These menu options can only be used in M model cars. (codable in NBT)

Show KW/MW radio band
• on
• show MW menu
• show KW menu
• off
Use this function to enable or hide the MW and KW menus in the radio menu. (codable in NBT)

Automatic time setting 2/2
• on
• on (alternative)
• off
When daylight savings time is active/not active, automatically update the time. Only change with ‘Automatic time setting 1/2’. (codable in NBT)

Turn on door lights in reverse gear
• on
• off
Turn on door lights while car is in reverse. This function can be used to illuminate the area while reversing in order to get a better view of the sides of the car. (codable in BDC)

Blind spot detection – speed
• 10 kph / 6 mph
• 20 kph / 12 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
Speed at which the blind spot detection is turned on. This function has only an effect if the car is equipped with a blind spot detection. (codable in ICM)

Sport mode configurable in iDrive
• on
• off
• off (alternative)
Sport mode can be configured in the iDrive menu. This function will appear in the iDrive settings under drive mode settings. If this function is available in the ICM module, you have to activate it, too. (codable in CIC)

Easy entry
• on
• off
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in BDC)

Close window after easy entry
• on
• off
If the driver side window has been opened via easy entry, the window automatically closes upon locking the vehicle. (codable in BDC)

Easy entry with every door open
• on
• off
Activate easy entry every time the car is unlocked. If this function is deactivated, the easy entry is activated by pressing the unlock button on the keyfob twice. (codable in BDC)

Start/Stop notification in dashboard
• on
• off
When the engine start/stop function is available the start/stop symbol in the dashboard appears. This function has only an effect if the dashboard is equipped with a start/stop symbol. (codable in KOMBI)

Start/Stop-Automatic memory
• on
• off
Setting for Start/Stop-Automatic is saved. This way the manual setting of the Start/Stop-Automatic button, i.e. whether the button is turned on or off, is saved for the next start. Deactivating the Start/Stop-Automatic on the car can increase the life time of the battery and the starter. (codable in BDC)

Start/Stop-Automatic default off
• on
• off
Engine start/stop automatic is turned off by default. (codable in BDC)

Start/Stop-Automatic enabled in ECO mode
• on
• off
Engine start/stop automatic is automatically activated in ECO mode. (codable in BDC)

Start in Eco / Eco Pro mode
• on
• off
When turning on the car, the ‘Eco / Eco Pro’ driving mode is automatically activated. Unfortunately, there is no possibility to automatically start the car in ‘Sport’ or ‘Sport+’ mode. (codable in ICM)

Default User Mode
• Sport Dynamic
• Sport Expert
• Sport Individual
• Comfort
• Comfort Plus
• Comfort Individual
• Eco Pro Efficient
• Eco Pro Plus
• Eco Pro Individual
• PHEV Sport Individual
• PHEV Hybrid Standard
• PHEV Electric Standard
• PHEV Electric Individual
• Adaptive
• PHEV Sport Standard
Use this coding to select the driving mode at engine start. If the selected mode is not available default value is delected automatically. (codable in GBDCMAIN)

Gear shift indicator and suggestion 1/3
• on
• off
Gear shift indicator in the on board computer. To activate this function, also activate other codings for ‘Gear shift indicator’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Gear shift indicator and suggestion 2/3
• on
• off
Only change with ‘Gear shift indicator 1/2’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Gear shift indicator in sport mode
• on
• off
Gear shift indicator is also shown in sport mode. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear shift indicator current gear
• on
• off
Current gear is permanently displayed in the gear shift indicator. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Gear Shift Indicator menu
• on
• off
Show menu in the iDrive settings to enable/disable the gear shift indicator. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in CIC)

Number until headlight cleaning
• 1
• 5
• 10
• 15
Head lights are cleaned every x-th time the windscreen washer has been activated. (codable in BDC)

Head light cleaning
• on
• off
Turn head light cleaning on/off. (codable in BDC)

Maximum speed headlight cleaning
• 6 kph / 4 mph
• 12 kph / 8 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
• 80 kph / 50 mph
• 130 kph / 80 mph
Maximum speed at which folding headlight cleaning is possible. (codable in BDC)

Number of splashes for head lights
• 1
• 2
• 3
Number of splashes for cleaning the head lights. (codable in BDC)

Length of splash for head lights
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Length of a single splash for head light cleaning. (codable in BDC)

Delay between splashes for head lights
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Delay between splashes for head light cleaning. (codable in BDC)

Cleanings until 1st headlight cleaning
• off
• 1
• 3
• 5
• 8
• 10
• 15
Head lights are cleaned for the first time after the x-th time the windscreen washer has been activated. (codable in BDC)

Cruise Control in Head-Up Display
• on
• off
Only change this function with ‘Cruise Control in Head-Up Display 1/2’. To activate this function also activate ‘Cruise Control in Head-Up Display’ in the iDrive module. (codable in KOMBI)

Turn signal in Head-Up Display
• on
• off
Show turn signals and hazard lights in the head up display. This function only works on models until 2013. To enable this option, please also activate ‘Turn signals in Head-Up Display – Addition’ in the iDrive module. (codable in KOMBI)

Startscreen HUD
• on
• off
Show startscreen when HUD starts. (codable in KOMBI)

Entertainment menu in HUD
• on
• off
Show radio stations and track list in Head-Up Display. (codable in KOMBI)

Recent call list in HUD
• on
• off
Show recent call list in Head-Up Display. (codable in KOMBI)

Telephone contacts in HUD
• on
• off
Show telephone contacts in Head-Up Display. (codable in KOMBI)

Cruise Control in HUD – addition
• on
• off
Only change this function with ‘Cruise Control in Head-Up Display ‘. This function needs to be activated in additon. (codable in KOMBI)

Color of Navigation Graphics
• orange
• HUD orange, Instruments gray
Use this function to change the color of navigation graphics in cluster (Head-Up and instrument cluster display). (codable in KOMBI)

HUD Startup time
• off
• very short
• short
• medium
• long
• very long
Time for start logo screen when Head-Up display is turned on. (codable in KOMBI)

Turn signal in Head-Up Display – Addition
• on
• off
Only change this function with ‘Turn singal in Head-Up Display’. (codable in KOMBI)

Voice command in HUD
• on
• off
Display voice command confirmation information in Head-Up Display. (codable in KOMBI)

Lane change in Head-Up Display
• on
• off
Use this function to show lane change warning in the head up display. (codable in KOMBI)

Cruise Control in Head-Up Display
• on
• off
Show cruise control in head-up display whenever cruise control is turned on. To activate this function also activate ‘Cruise Control in Head-Up Display’ in the Kombi module. (codable in CIC)

Turn signals in Head-Up Display
• on
• off
Show menu in the iDrive to turn on signals and hazard lights in the head up display. To activate this function, please activate ‘Turn signals in Head-Up Display’ in the HUD/Kombi module. (codable in CIC)

Highway junction images on HUD
• on
• off
Show Highway junction images on HUD. (codable in CIC)

Entertainment/Telephone information in HUD
• on
• off
Adds checkbox in Head Up Display settings for entertainment/telephone in iDrive. To show information for entertainment and telephone, please also activate the HUD functions in the Kombi module. (codable in CIC)

Front fog lights with high beams
• on
• off
Front fog lights are automatically turned off when activating high beams. (codable in BDC)

iDrive start logo
• BMW Connected Drive (Version 1)
• BMW Connected Drive (Version 2)
• M Performance
• Alpina Tuning
• BMW i
• BMW white
• BMW brown
• Mini
• Rolls Royce
• BMW Christmas
Logo that is displayed when starting the iDrive system. (codable in NBT)

iDrive start animated
• not animated
• animated
• black screen
Logo that is displayed when starting the iDrive system is animated. Alternatively a black screen without any logo can be displayed. (codable in NBT)

Audible confirmation menu
• on
• off
Show menu for audible confirmation for locking/unlocking in iDrive. This coding only works when the FZD module is installed. (codable in CIC)

Sport mode configurable in iDrive
• on
• off
• off (alternative)
Sport mode can be configured in the iDrive menu. This function will appear in the iDrive settings under drive mode settings. If this function is available in the ICM module, you have to activate it, too. (codable in CIC)

Tire pressure menu with temperature
• on
• off
Also show temperature of the individual tires in the tire pressure menu. This function only works if the tires have tire pressure sensors installed and pressure of the individual tires is already shown. This feature only affects the display of the tire pressure menu in the iDrive, it can not be used to disable the tire pressure monitor. (codable in CIC)

Message length while driving
• no details
• one page
• up to five pages
• whole text
Length of displayed messages for available office functions while driving, e.g. SMS. (codable in CIC)

Sport display
• on
• off
Sport display for current performance and torque is shown in the ‘Vehicle information’. Since some engines (especially diesel ones) do not provide the data for the sport display to the iDrive, the sport display might be inactive and permanently show ‘0’ even after enabling this function. (codable in CIC)

Sport display – units
• on
• off
Show menu in the iDrive settings to change the units for the sport display. (codable in CIC)

Gear Shift Indicator menu
• on
• off
Show menu in the iDrive settings to enable/disable the gear shift indicator. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in CIC)

Phone contacts in ‘Office’ iDrive menu
• on
• off
Also display phone contacts in the iDrive menu ‘Office’ in addition contacts stored in the car itself. Turn this function off to only display the contacts from the car itself. (codable in NBT)

Volume popup
• on
• off
Show volume popup in the iDrive when changing the volume. (codable in NBT)

Sport display – color
• red
• orange
Color of the sport display. Red is usually used in M-models. (codable in NBT)

Tire pressure menu in iDrive 1/3
• off
• pressure
• pressure and temperature
Tire pressure menu in iDrive is shown with pressure and optionally temperature. Displaying values only works if the tires have tire pressure sensors installed. This feature only affects the display of the tire pressure menu in the iDrive, it can not be used to disable the tire pressure monitor. (codable in NBT)

Tire pressure menu in iDrive 2/3
• on
• off
Only change this function with ‘Tire pressure menu in iDrive 1/3’. (codable in NBT)

Tire pressure menu in iDrive 3/3
• on
• off
• off (alternative)
Only change this function with ‘Tire pressure menu in iDrive 1/3’. (codable in NBT)

Messages while driving
• while driving
• only with handbrake
• only in ‘P’ position
• only with handbrake and ‘P’ position
• only with handbrake or ‘P’ position
Display messages of available office functions while driving, e.g. SMS. (codable in NBT)

Sport mode configurable in iDrive
• on
• off
Sport mode can be configured in the iDrive menu. This function needs to be turned on in the iDrive module as well. The function will appear in the iDrive settings under drive mode settings. (codable in ICM)

Digital speedometer
• on
• off
The current speed is shown in the digital display below the speedometer. (codable in KOMBI)

‘Correction’ speedometer
• ‘corrected’ speed
• true speed
This coding does not work on US models. Per default the speed shown in the speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)

Blank information display in dashboard
• on
• off
Blank information display in dashboard is shown when you switch the information displays with the BC button. (codable in KOMBI)

Cruise Control speed display
• off
• 3 s
• 5 s
The set speed of the cruise control is shown for a couple of seconds in the on board computer. (codable in KOMBI)

Date in dashboard
• on
• off
Show date in dashboard. (codable in KOMBI)

GPS time correction
• on
• off
Time of day is corrected by using GPS. (codable in KOMBI)

Gear shift indicator and suggestion 1/3
• on
• off
Gear shift indicator in the on board computer. To activate this function, also activate other codings for ‘Gear shift indicator’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Gear shift indicator and suggestion 2/3
• on
• off
Only change with ‘Gear shift indicator 1/2’. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. It suggests the best gear only in M6T. (codable in KOMBI)

Date incl. Time in dashboard
• on
• off
Show date including current time in the dashboard. In order to activate this function, please also activate ‘Date in dashboard’. (codable in KOMBI)

Gear shift indicator in sport mode
• on
• off
Gear shift indicator is also shown in sport mode. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Start/Stop notification in dashboard
• on
• off
When the engine start/stop function is available the start/stop symbol in the dashboard appears. This function has only an effect if the dashboard is equipped with a start/stop symbol. (codable in KOMBI)

Bootlogo for dashboard
• BMW
• M Performance
Bootlogo for dashboard when ignition is turned on. This function only works if the dashboard display reaches at least from the middle to under the rpm meter. This coding shows no effect on smaller displays. (codable in KOMBI)

Gear shift indicator current gear
• on
• off
Current gear is permanently displayed in the gear shift indicator. Since some gearbox types (especially automatic) do not provide the data for the Gear Shift Indicator to the KOMBI, the Gear Shift Indicator might be inactive or permanently show no current gear, even after enabling this function. (codable in KOMBI)

Color of Navigation Graphics
• orange
• HUD orange, Instruments gray
Use this function to change the color of navigation graphics in cluster (Head-Up and instrument cluster display). (codable in KOMBI)

Display compass
• on
• off
Show the compass in board computer (OBC). Select compass by pushing the ‘BC’ button on the left side of the indicator arm. (codable in KOMBI)

Off-Mode Memory
• on
• off
Save setting for ‘Off-mode’ for the air conditioning. (codable in IHKA)

Save circulation settings
• on
• off
Circulation settings are saved for next start of the vehicle. (codable in IHKA)

Automatic compressor with air conditioning
• on
• off
When pressing the ‘Automatic’ button for air conditioning, the compressor for air conditioning does not start by itself. (codable in IHKA)

Automatic compressor with recirculation
• on
• off
When pressing the ‘Recirculation’ button for air conditioning, the compressor for air conditioning does not start by itself. (codable in IHKA)

Automatic reset to circulating air
• on
• off
Automatically reset to fresh air after a certain time when the recirculation mode of the A/C is active. (codable in IHKA)

Legal disclaimer (US)
• off
• on
• permanent
Show legal disclaimer when iDrive is started. This warning is usually only shown in US-models. (codable in CIC)

Camera disclaimer
• off
• on
• permanent
Show legal disclaimer for rear view camera. (codable in CIC)

Night Vision disclaimer
• off
• on
• permanent
Show legal disclaimer for night vision view camera. (codable in CIC)

Optical confirmation – locking vehicle
• off
• 1
• 2
• 3
Number of times the turn signals are turned on when locking the vehicle. (codable in BDC)

Comfort close sunroof immediately
• on
• off
Start closing the sunroof immediately during comfort closing. (codable in BDC)

Comfort close windows simultaneously
• on
• off
Front and back windows close simultaneously during comfort closing. (codable in BDC)

Comfort close using remote
• on
• off
Press and hold the lock button on the remote to close all windows and the sunroof. (codable in BDC)

Comfort close – door (comfort access)
• on
• off
Use comfort closing features when locking with the door handle. This only works if comfort access is installed. Touch the locking area on the door handle for a longer time to close all windows and the sunroof. (codable in BDC)

Comfort closing delay (mirrors)
• 0.0s
• 0.5s
• 1.5s
General delay for comfort closing. If ‘0.0s’ is set, mirrors fold immediately when car is locked. (codable in BDC)

Audible confirmation after complete closing
• on
• off
Audible confirmation for locking vehicle is active/not active. Confirmation will occur after every door and the tailgate are closed. (codable in FZD)

Optical confirmation – locking vehicle
• on
• off
Optical confirmation for locking vehicle is active/not active. (codable in FZD)

Optical confirmation after complete closing
• on
• off
Optical confirmation for locking vehicle is active/not active. Confirmation will occur after every door and the tailgate are closed. (codable in FZD)

Optical confirmation – tail gate
• on
• off
When the trunk/tail gate is closed while the car is locked the turn signals blink. This coding only works if Comfort Access is installed in the car. (codable in FZD)

Audible confirmation – locking vehicle
• on
• off
Audible confirmation for locking vehicle is active/not active. (codable in FZD)

Comfort folding for sideview mirrors
• on
• off
This function requires an installed LIN-Bus (usually installed with mirror heating).nWhen holding the lock/unlock button on the remote the sideview mirrors automatically fold/unfold. May need additional coding of the ‘CAS’ module. (codable in BDC)

Unfold mirrors after comfort close
• on
• off
Mirrors are automatically unfolded when the car is unlocked, if they were folded by the comfort closing function. (codable in BDC)

Auto-Unfold mirrors
• 1 kph / 1 mph
• 10 kph / 6 mph
• 20 kph / 12 mph
• 40 kph / 25 mph
Speed at which folded mirrors are automatically unfolded. (codable in BDC)

Mirror tilt 1/2
• on
• off
Requirement for mirror tilt functions. (codable in BDC)

Mirror tilt 2/2
• on
• off
Requirement for mirror tilt functions. (codable in BDC)

Tilt mirror in reverse
• on
• off
This function requires an installed LIN-Bus (usually installed with mirror heating).nPassenger mirror is tilted when switching into reverse gear and the mirror switch is set to the driver side. To activate this function activate ‘Mirror tilt’ as well. (codable in BDC)

Mirror tilt while reversing
• weak
• medium
• strong
Tilt of mirrors with activated reverse gear. In order to activate this function, please also activate ‘Tilt mirror in reverse’. (codable in BDC)

Mirror fold with hazard lights
• on
• off
Mirrors can be folded via comfort closing while hazard lights are active. (codable in BDC)

Maximum speed mirror fold
• 10 kph / 6 mph
• 20 kph / 12 mph
• 40 kph / 25 mph
• 60 kph / 37 mph
Maximum speed at which folding the mirrors is possible. (codable in BDC)

Navigation fuel stop suggestion
• on
• off
Show suggestions for fuel stops along the way to the destination in ‘Route info’ when navigation system is active. (codable in CIC)

Route Info
• on
• off
Display the ‘Route Info’ menu. In the ‘Route Info’ menu you can check the current navigation turn by turn. (codable in CIC)

Navigation geo coordinates
• on
• off
Show geo coordinates in latitude and longitude in the navigation menu. (codable in CIC)

Navigation while updating
• on
• off
Allow using the navigation system while the maps are being updated. (codable in CIC)

Arrow view in main window
• on
• off
Arrow view is also available in the main window and not only in the split screen window. (codable in CIC)

Navigation current position
• on
• off
Show option to display current position in the navigation menu. (codable in CIC)

Range map
• on
• off
Range map is available in the main window as a possible map. (codable in NBT)

Route magnet
• on
• off
Display route magnet as a possible method for recalculating the active route. (codable in NBT)

Route preview
• on
• off
Display the route preview menu. This function is also known as ‘Route simulator’. If available, also activate ‘Route preview – addition’. (codable in NBT)

Route preview – addition
• on
• off
Only change this function with ‘Route preview’. (codable in NBT)

Optical confirmation – unlocking vehicle
• off
• 1
• 2
• 3
Number of times the turn signals are turned on when unlocking the vehicle. (codable in BDC)

Comfort open sunroof immediately
• on
• off
Start opening the sunroof immediately during comfort opening. (codable in BDC)

Comfort open windows simultaneously
• on
• off
Front and back windows open simultaneously during comfort opening. (codable in BDC)

Comfort open using remote
• on
• off
Press and hold the unlock button on the remote to open all windows and the sunroof. (codable in BDC)

Comfort open delay
• 0.0 s
• 0.5 s
• 1.5 s
• 2.5 s
General delay for comfort opening. If ‘0.0s’ is set, comfort opening is immediately started when the car is unlocked. (codable in BDC)

Easy entry
• on
• off
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in BDC)

Close window after easy entry
• on
• off
If the driver side window has been opened via easy entry, the window automatically closes upon locking the vehicle. (codable in BDC)

Easy entry with every door open
• on
• off
Activate easy entry every time the car is unlocked. If this function is deactivated, the easy entry is activated by pressing the unlock button on the keyfob twice. (codable in BDC)

Optical confirmation – unlocking vehicle
• on
• off
Optical confirmation for unlocking vehicle is active/not active. (codable in FZD)

Audible confirmation – unlocking vehicle
• on
• off
Audible confirmation for unlocking vehicle is active/not active. (codable in FZD)

PDC view
• vertical (F-Models)
• horizontal (E-Models)
Direction of park distance control view. (codable in CIC)

PDC in reverse
• on
• off
Activate PDC as soon as car is rolling backwards/reversing. (codable in PDC)

Warning sound volume front
• very weak
• weak
• medium
• strong
• very strong
Volume for the warning sound of the front PDC. (codable in PDC)

Warning sound volume rear
• very weak
• weak
• medium
• strong
• very strong
Volume for the warning sound of the rear PDC. (codable in PDC)

PDC turn off – distance limit
• when putting in forward gear
• 1 m / 3 ft
• 10 m / 33 ft
• 20 m / 66 ft
• 50 m / 164 ft
• 75 m / 264 ft
• 100 m / 330 ft
• 150 m / 500 ft
• 200 m / 660 ft
• 250 m / 820 ft
PDC is turned off automatically after driving the set distance in forward gear in one piece. (codable in PDC)

PDC turn off – speed limit
• when putting in forward gear
• 1 kph / 1 mph
• 10 kph / 6 mph
• 20 kph / 12 mph
• 36 kph / 22 mph
PDC is turned off automatically after driving faster than the set speed in forward gear. (codable in PDC)

Reversing camera turn off – distance limit
• when putting in forward gear
• 1 m / 3 ft
• 10 m / 33 ft
• 20 m / 66 ft
• 50 m / 164 ft
• 75 m / 264 ft
• 100 m / 330 ft
• 150 m / 500 ft
• 200 m / 660 ft
• 250 m / 820 ft
Reversing camera is turned off automatically after driving the set distance in forward gear in one piece. (codable in PDC)

Reversing camera turn off – speed limit
• when putting in forward gear
• 1 kph / 1 mph
• 10 kph / 6 mph
• 20 kph / 12 mph
• 36 kph / 22 mph
Reversing camera is turned off automatically after driving faster than the set speed in forward gear. (codable in PDC)

Fog lights with standing lights
• on
• off
Fog lights can be turned on when the light switch is in the standing lights position. (codable in BDC)

Parking lights
• on
• off
Parking lights function is active/not active. One sided parking lights are activated by turning on the turn signals after turning off the ignition and locking the car. (codable in BDC)

Continue window action when door is opened
• on
• off
When the door is opened while its window is opening/closing, the window will continue opening/closing the window. (codable in BDC)

Easy entry
• on
• off
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in BDC)

Close window after easy entry
• on
• off
If the driver side window has been opened via easy entry, the window automatically closes upon locking the vehicle. (codable in BDC)

Easy entry with every door open
• on
• off
Activate easy entry every time the car is unlocked. If this function is deactivated, the easy entry is activated by pressing the unlock button on the keyfob twice. (codable in BDC)

Rain light sensor sensitivity
• very sensitive
• sensitive
• normal
• insensitive
• daytime running lights
• standard
Sensitivity of rain light sensor. (codable in BDC)

Rear fog lights
• on
• off
Activate rear fog light function. To activate this function, please also activate the rear fog lights in the REM module. (codable in GBDCMAIN)

Seating heater memory
• off
• 15 min
• 24 hours
• permanent
The current setting of the seating heater is saved when the engine is turned off. (codable in SM_FA)

Easy entry/exit aid
• off
• driver
• passenger
When entering/leaving the car the seat is widened (with the lumbar width adjustment) so entering/leaving the car is easier. (codable in SM_FA)

Seat position memory confirmation
• on
• off
When saving the seat position with the memory buttons in the car, a short Gong sound is played. (codable in SM_FA)

Seat heater temp. level 1 – armrest front
• 25°C / 77°F
• 26°C / 79°F
• 27°C / 81°F
• 28°C / 82°F
• 29°C / 84°F
• 30°C / 86°F
• 31°C / 88°F
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
Temperature of the front armrest heater for driver and passenger with front seat heater activated on level 1. (codable in BDC)

Seat heater temp. level 2 – armrest front
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
Temperature of the front armrest heater for driver and passenger with front seat heater activated on level 2. (codable in BDC)

Seat heater temp. level 3 – armrest front
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
• 45°C / 113°F
• 46°C / 115°F
• 47°C / 117°F
• 48°C / 118°F
• 49°C / 120°F
• 50°C / 122°F
Temperature of the front armrest heater for driver and passenger with front seat heater activated on level 3. (codable in BDC)

Seat heater temp. level 1 – seat front
• 25°C / 77°F
• 26°C / 79°F
• 27°C / 81°F
• 28°C / 82°F
• 29°C / 84°F
• 30°C / 86°F
• 31°C / 88°F
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
Temperature of the front seat heater for driver and passenger with seat heater activated on level 1. (codable in BDC)

Seat heater temp. level 2 – seat front
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
Temperature of the front seat heater for driver and passenger with seat heater activated on level 2. (codable in BDC)

Seat heater temp. level 3 – seat front
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
• 45°C / 113°F
• 46°C / 115°F
• 47°C / 117°F
• 48°C / 118°F
• 49°C / 120°F
• 50°C / 122°F
Temperature of the front seat heater for driver and passenger with seat heater activated on level 3. (codable in BDC)

Seat heater temp. level 1 – armrest rear
• 25°C / 77°F
• 26°C / 79°F
• 27°C / 81°F
• 28°C / 82°F
• 29°C / 84°F
• 30°C / 86°F
• 31°C / 88°F
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
Temperature of the rear armrest heater with rear seat heater activated on level 1. (codable in BDC)

Seat heater temp. level 2 – armrest rear
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
Temperature of the rear armrest heater with rear seat heater activated on level 2. (codable in BDC)

Seat heater temp. level 3 – armrest rear
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
• 45°C / 113°F
• 46°C / 115°F
• 47°C / 117°F
• 48°C / 118°F
• 49°C / 120°F
• 50°C / 122°F
Temperature of the rear armrest heater with rear seat heater activated on level 3. (codable in BDC)

Seat heater temp. level 1 – seat rear
• 25°C / 77°F
• 26°C / 79°F
• 27°C / 81°F
• 28°C / 82°F
• 29°C / 84°F
• 30°C / 86°F
• 31°C / 88°F
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
Temperature of the rear seat heater with seat heater activated on level 1. (codable in BDC)

Seat heater temp. level 2 – seat rear
• 32°C / 90°F
• 33°C / 91°F
• 34°C / 93°F
• 35°C / 95°F
• 36°C / 97°F
• 37°C / 99°F
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
Temperature of the rear seat heater with seat heater activated on level 2. (codable in BDC)

Seat heater temp. level 3 – seat rear
• 38°C / 100°F
• 39°C / 102°F
• 40°C / 104°F
• 41°C / 106°F
• 42°C / 108°F
• 43°C / 109°F
• 44°C / 111°F
• 45°C / 113°F
• 46°C / 115°F
• 47°C / 117°F
• 48°C / 118°F
• 49°C / 120°F
• 50°C / 122°F
Temperature of the rear seat heater with seat heater activated on level 3. (codable in BDC)

Seating heater memory
• off
• 15 min
• 24 hours
• permanent
The current setting of the seating heater is saved when the engine is turned off. (codable in SM_FA)

US Sidemarker left brightness
• off
• very low
• low
• medium
• high
• very high
Brightness of the US Sidemarker on the left side. (codable in BDC)

US Sidemarker right brightness
• off
• very low
• low
• medium
• high
• very high
Brightness of the US Sidemarker on the right side. (codable in BDC)

US Sidemarker left
• on
• off
• off (alternative)
Light for the US Sidemarker on the left side. If switch setting is ‘0’, the function does not have an effect. If switch setting is ‘A’, the function does only have an effect if it’s dark. In addition the brightness has to be set to ‘High’. (codable in BDC)

US Sidemarker right
• off
• on
• off (alternative)
Light for the US Sidemarker on the right side. If switch setting is ‘0’, the function does not have an effect. If switch setting is ‘A’, the function does only have an effect if it’s dark. In addtion the brightness has to be set to ‘High’. (codable in BDC)

Digital speedometer
• on
• off
The current speed is shown in the digital display below the speedometer. (codable in KOMBI)

‘Correction’ speedometer
• ‘corrected’ speed
• true speed
This coding does not work on US models. Per default the speed shown in the speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)

Digital Speed Display
• off
• kmh
• kmh (Option 2)
• mph
• mph (Option 2)
Use this function to display digital speed in instrument cluster. Digital speedometer setting must be enabled in iDrive display settings. (codable in KOMBI)

Raising speed for spoiler
• 55 kph / 35 mph
• 75 kph / 50 mph
• 95 kph / 60 mph
• 110 kph / 70 mph
Vehicle speed in kph or mph at which spoiler automatically raises. Raising speed has to be higher than the lowering speed. The lowering speed can be changed with ‘lowering speed spoiler’. This function will only have an effect if the car is equipped with an electrical spoiler. (codable in HKL2)

Lowering speed for spoiler 2/2
• 55 kph / 35 mph
• 75 kph / 50 mph
• 95 kph / 60 mph
• 110 kph / 70 mph
Only change this function with ‘Lowering speed for spoiler 1/2’. (codable in HKL2)

Lowering speed spoiler 1/2
• 50 kph / 31 mph
• 70 kph / 45 mph
• 90 kph/ 55 mph
Vehicle speed in kph or mph at which spoiler automatically lowers. Lowering speed has to be lower than the raising speed. The raising speed can be changed with ‘Raising speed spoiler’. This function will only have an effect if the car is equipped with an electrical spoiler. (codable in HKL2)

Sport display – unit for performance
• hp
• kW
Unit for performance in the sport display in the iDrive (if available). (codable in KOMBI)

Sport display – unit for torque
• Nm
• lb ft
• kgm
Unit for torque in the sport display in the iDrive (if available). (codable in KOMBI)

Sport display
• on
• off
Sport display for current performance and torque is shown in the ‘Vehicle information’. Since some engines (especially diesel ones) do not provide the data for the sport display to the iDrive, the sport display might be inactive and permanently show ‘0’ even after enabling this function. (codable in CIC)

Sport display – units
• on
• off
Show menu in the iDrive settings to change the units for the sport display. (codable in CIC)

Sport display – color
• red
• orange
Color of the sport display. Red is usually used in M-models. (codable in NBT)

Optical confirmation – tail gate
• on
• off
When the trunk/tail gate is closed while the car is locked the turn signals blink. This coding only works if Comfort Access is installed in the car. (codable in FZD)

Close trunk with keyfob
• on
• off
Close the trunk/rear lid via the keyfob. If available, also activate ‘Close trunk with keyfob – addition’. (codable in HKL – the HKL module is only available, if the car has a button to electronically close the tailgate/trunk lid)

Close trunk with footwell switch
• on
• off
Close the trunk/rear lid with the interior footwell switch. (codable in HKL – the HKL module is only available, if the car has a button to electronically close the tailgate/trunk lid)

Close trunk with keyfob – addition
• on
• off
Only change this function with ‘Close trunk with keyfob’. (codable in HKL – the HKL module is only available, if the car has a button to electronically close the tailgate/trunk lid)

Threshold for low range warning
• off
• 8 km
• 10 km / 6 mi
• 20 km / 12 mi
• 50 km / 31 mi
• 8 mi
• 15 mi
• 30 mi
Threshold for low range warning due to low fuel level. (codable in KOMBI)

Threshold for fuel reserve warning
• off
• 15 km
• 20 km / 12 mi
• 50 km / 31 mi
• 90 km
• 15 mi
• 30 mi
• 50 mi
Use this function to change the threshold for the low range warning due to low fuel level. (codable in KOMBI)

Recent call list in HUD
• on
• off
Show recent call list in Head-Up Display. (codable in KOMBI)

Telephone contacts in HUD
• on
• off
Show telephone contacts in Head-Up Display. (codable in KOMBI)

Selection of ringtone
• BMW
• Mini
Selection of the ringtone which sounds when a call comes in. To use the ringtone of your phone, please turn ‘Use telephone ringtone’ on. (codable in CIC)

Use telephone ringtone
• on
• off
Playback of the telephone ringtone on the car speakers. (codable in CIC)

Message length while driving
• no details
• one page
• up to five pages
• whole text
Length of displayed messages for available office functions while driving, e.g. SMS. (codable in CIC)

Phone contacts in ‘Office’ iDrive menu
• on
• off
Also display phone contacts in the iDrive menu ‘Office’ in addition contacts stored in the car itself. Turn this function off to only display the contacts from the car itself. (codable in NBT)

Siri Eyes-Free button
• on
• off
When pressing and holding the voice command button on the steering wheel ‘Siri Eyes-Free’ is activated. This function can only be used by iOS devices. Siri has to be active on the iPhone. (codable in NBT)

Messages while driving
• while driving
• only with handbrake
• only in ‘P’ position
• only with handbrake and ‘P’ position
• only with handbrake or ‘P’ position
Display messages of available office functions while driving, e.g. SMS. (codable in NBT)

Number of addresses/messages for storing
• 1
• 5
• 10
• 20
• 25
• 30
• 40
• 50
Maximum number of messages/addresses to be stored in the car. (codable in COMBOX)

Tyre pressure monitoring system
• on
• off
Use this function to turn off the tyre pressure monitoring system (TPMS). This coding can’t be used to retrofit TPMS to a car. (codable in KOMBI)

Tire pressure menu in iDrive 1/3
• off
• pressure
• pressure and temperature
Tire pressure menu in iDrive is shown with pressure and optionally temperature. Displaying values only works if the tires have tire pressure sensors installed. This feature only affects the display of the tire pressure menu in the iDrive, it can not be used to disable the tire pressure monitor. (codable in NBT)

Tire pressure menu in iDrive 2/3
• on
• off
Only change this function with ‘Tire pressure menu in iDrive 1/3’. (codable in NBT)

Tire pressure menu in iDrive 3/3
• on
• off
• off (alternative)
Only change this function with ‘Tire pressure menu in iDrive 1/3’. (codable in NBT)

Turn signal in Head-Up Display
• on
• off
Show turn signals and hazard lights in the head up display. This function only works on models until 2013. To enable this option, please also activate ‘Turn signals in Head-Up Display – Addition’ in the iDrive module. (codable in KOMBI)

Turn signal in Head-Up Display – Addition
• on
• off
Only change this function with ‘Turn singal in Head-Up Display’. (codable in KOMBI)

One-touch turn signal function
• 1
• 3
Number of turn signals when tapping the turn signal. In some cases, this option also needs to be enabled in the iDrive. (codable in BDC)

Optical confirmation – unlocking vehicle
• off
• 1
• 2
• 3
Number of times the turn signals are turned on when unlocking the vehicle. (codable in BDC)

Optical confirmation – locking vehicle
• off
• 1
• 2
• 3
Number of times the turn signals are turned on when locking the vehicle. (codable in BDC)

Turn signals in Head-Up Display
• on
• off
Show menu in the iDrive to turn on signals and hazard lights in the head up display. To activate this function, please activate ‘Turn signals in Head-Up Display’ in the HUD/Kombi module. (codable in CIC)

Optical confirmation – unlocking vehicle
• on
• off
Optical confirmation for unlocking vehicle is active/not active. (codable in FZD)

Optical confirmation – locking vehicle
• on
• off
Optical confirmation for locking vehicle is active/not active. (codable in FZD)

Alarm with turn signals
• on
• off
Turn signals blink when alarm is initiated. (codable in FZD)

Video in motion 1/3
• off
• 3 kph / 2 mph
• 8 kph / 5 mph
• on
Enable video and DVD while driving. This is only possible if the car supports watching TV or playing DVDs while standing. In order to enable this option, activate ‘Video in motion 2/3’ and ‘Video in motion 3/3’ as well. If available, also disable ‘Video only with handbrake’. (codable in CIC)

Video in motion 2/3
• off
• 3 kph / 2 mph
• 10 kph / 6 mph
• on
Only change this function with ‘Video in motion 1/3’. This is only possible if the car supports watching TV or playing DVDs while standing. (codable in CIC)

Video in motion 3/3
• on
• off
Only change this function with ‘Video in motion 1/3’. This is only possible if the car supports watching TV or playing DVDs while standing. (codable in CIC)

Video in motion menu
• on
• off
Enable menu to activate video and DVD while driving. This is only possible if the car supports watching TV or playing DVDs while standing. To deactivate video in motion, please deactivate and activate this coding again and follow the steps afterwards. (codable in NBT)

Video only with handbrake
• on
• off
Only allow watching video while the handbrake is pulled. In order to watch video while driving, set this function to ‘not active’ and activate all parts of ‘Video in motion’. Video in motion is only possible if the car supports watching TV or playing DVDs while standing. If available, also deactivate ‘Video only with handbrake – addition’. (codable in NBT)

Video format support 1/3
• on
• off
Enable playback of videos in more video formats. (codable in NBT)

Video format support 2/3
• on
• off
Only change this function with ‘Video format support 1/3’. (codable in NBT)

Video format support 3/3
• on
• off
Only change this function with ‘Video format support 1/3’. (codable in NBT)

DVD menu button during playing
• DVD menu button
• title list button
When playing a DVD instead of the ‘Title list’ button a button is shown to activate the own menu of the DVD, like on a DVD player. (codable in NBT)

Video Playback via USB
• on
• off
• off (alternative)
Play videos on a USB-Stick. (codable in NBT)

Video Playback from iPhone
• on
• off
• off (alternative)
Play videos from iPhone. This only works if the iPhone is connected via a snap-in adapter. This does not work if the iPhone is connected via a USB cable. (codable in NBT)

Video only with handbrake – addition
• off
• only with handbrake
• only in ‘P’ position
• only with handbrake and ‘P’ position
• only with handbrake or ‘P’ position
Only change this function with ‘Video only with handbrake’. (codable in NBT)

Low beams left voltage monit. 1/2
• on
• off
Voltage monitoring for low beams left. Might cause flickering of LED lights. (codable in BDC)

Low beams left voltage monit. 2/2
• on
• off
Deactivate with ‘Low beams left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Low beams right voltage monit. 1/2
• on
• off
Voltage monitoring for low beams right. Might cause flickering of LED lights. (codable in BDC)

Low beams right voltage monit. 2/2
• on
• off
Deactivate with ‘Low beams right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

High beams left voltage monit. 1/2
• on
• off
Voltage monitoring for high beams left. Might cause flickering of LED lights. (codable in BDC)

High beams left voltage monit. 2/2
• on
• off
Deactivate with ‘High beams left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

High beams right voltage monit. 1/2
• on
• off
Voltage monitoring for high beams right. Might cause flickering of LED lights. (codable in BDC)

High beams right voltage monit. 2/2
• on
• off
Deactivate with ‘High beams right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Turn signals front left voltage monit. 1/2
• on
• off
Voltage monitoring for turn signals front left. Might cause flickering of LED lights. (codable in BDC)

Turn signals front left voltage monit. 2/2
• on
• off
Deactivate with ‘Turn signals front left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Turn signals front right voltage monit. 1/2
• on
• off
Voltage monitoring for turn signals front right Might cause flickering of LED lights. (codable in BDC)

Turn signals front right voltage monit. 2/2
• on
• off
Deactivate with ‘Turn signals front right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Front fog lights left voltage monit. 1/2
• on
• off
Voltage monitoring for front fog lights left. Might cause flickering of LED lights. (codable in BDC)

Front fog lights left voltage monit. 2/2
• on
• off
Deactivate with ‘Front fog lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Front fog lights right voltage monit. 1/2
• on
• off
Voltage monitoring for front fog lights right. Might cause flickering of LED lights. (codable in BDC)

Front fog lights right voltage monit. 2/2
• on
• off
Deactivate with ‘Front fog lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Daytime running lights left voltage monit. 1/2
• on
• off
Voltage monitoring for daytime running lights left. Might cause flickering of LED lights. (codable in BDC)

Daytime running lights left voltage monit. 2/2
• on
• off
Deactivate with ‘Daytime running lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Daytime running lights right voltage monit. 1/2
• on
• off
Voltage monitoring for daytime running lights right. Might cause flickering of LED lights. (codable in BDC)

Daytime running lights right voltage monit. 2/2
• on
• off
Deactivate with ‘Daytime running lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Turn signals front left warning
• on
• off
Warning for malfunction of Turn signals front left in the on board computer. (codable in BDC)

Turn signals front right warning
• on
• off
Warning for malfunction of Turn signals front right in the on board computer. (codable in BDC)

Turn signals rear left voltage monit. 1/2
• on
• off
Voltage monitoring for turn signals rear left. Might cause flickering of LED lights. (codable in BDC)

Turn signals rear left voltage monit. 2/2
• on
• off
Deactivate with ‘Turn signals rear left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Turn signals rear right voltage monit. 1/2
• on
• off
Voltage monitoring for turn signals rear right. Might cause flickering of LED lights. (codable in BDC)

Turn signals rear right voltage monit. 2/2
• on
• off
Deactivate with ‘Turn signals rear right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Standing lights outer rear left voltage monit. 1/2
• on
• off
Voltage monitoring for outer standing lights rear left. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights outer rear left voltage monit. 2/2
• on
• off
Deactivate with ‘Standing lights outer rear left voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights outer rear right voltage monit. 1/2
• on
• off
Voltage monitoring for outer standing lights rear right. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights outer rear right voltage monit. 2/2
• on
• off
Deactivate with ‘Standing lights outer rear right voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights inner rear left voltage monit. 1/2
• on
• off
Voltage monitoring for inner standing lights rear left. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights inner rear left voltage monit. 2/2
• on
• off
Deactivate with ‘Standing lights inner rear left voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights inner rear right voltage monit. 1/2
• on
• off
Voltage monitoring for inner standing lights rear right. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights inner rear right voltage monit. 2/2
• on
• off
Deactivate with ‘Standing lights inner rear right voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Reversing lights left voltage monit. 1/2
• on
• off
Voltage monitoring for reversing lights left. Might cause flickering of LED lights. (codable in BDC)

Reversing lights left voltage monit. 2/2
• on
• off
Deactivate with ‘Reversing lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Reversing lights right voltage monit. 1/2
• on
• off
Voltage monitoring for reversing lights right. Might cause flickering of LED lights. (codable in BDC)

Reversing lights right voltage monit. 2/2
• on
• off
Deactivate with ‘Reversing lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Rear fog light left voltage monit. 1/2
• on
• off
Voltage monitoring for rear left fog light. Might cause flickering of LED lights. (codable in BDC)

Rear fog light left voltage monit. 2/2
• on
• off
Deactivate with ‘Rear fog light left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Rear fog light right voltage monit. 1/2
• on
• off
Voltage monitoring for rear right fog light. Might cause flickering of LED lights. (codable in BDC)

Rear fog light right voltage monit. 2/2
• on
• off
Deactivate with ‘Rear fog light right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Brake lights left voltage monit. 1/2
• on
• off
Voltage monitoring for brake lights left. Might cause flickering of LED lights. (codable in BDC)

Brake lights left voltage monit. 2/2
• on
• off
Deactivate with ‘Brake lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Brake lights right voltage monit. 1/2
• on
• off
Voltage monitoring for brake lights right. Might cause flickering of LED lights. (codable in BDC)

Brake lights right voltage monit. 2/2
• on
• off
Deactivate with ‘Brake lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Third brake light voltage monit. 1/2
• on
• off
Voltage monitoring for third brake light. Might cause flickering of LED lights. (codable in BDC)

Third brake light voltage monit. 2/2
• on
• off
Deactivate with ‘Third brake light voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

License plate lighting voltage monit. 1/2
• on
• off
Voltage monitoring for license plate lighting. Might cause flickering of LED lights. (codable in BDC)

License plate lighting voltage monit. 2/2
• on
• off
Deactivate with ‘License plate lighting voltage monit. 1/2’ to disable flickering of LED lights. (codable in BDC)

Threshold for low range warning
• off
• 8 km
• 10 km / 6 mi
• 20 km / 12 mi
• 50 km / 31 mi
• 8 mi
• 15 mi
• 30 mi
Threshold for low range warning due to low fuel level. (codable in KOMBI)

Threshold for fuel reserve warning
• off
• 15 km
• 20 km / 12 mi
• 50 km / 31 mi
• 90 km
• 15 mi
• 30 mi
• 50 mi
Use this function to change the threshold for the low range warning due to low fuel level. (codable in KOMBI)

Temperature warning
• on
• off
Warning for outside temperature below 4° C / 39° F is active/not active. (codable in KOMBI)

Reverse gear gong
• on
• off
Gong for reverse gear is active/not active. (codable in KOMBI)

Low beams left warning
• on
• on (alternative)
• off
Warning for malfunction of Low beams left in the on board computer. (codable in BDC)

Low beams right warning
• on
• on (alternative)
• off
Warning for malfunction of Low beams right in the on board computer. (codable in BDC)

High beams left warning
• on
• on (alternative)
• off
Warning for malfunction of High beams left in the on board computer. (codable in BDC)

High beams right warning
• on
• on (alternative)
• off
Warning for malfunction of High beams right in the on board computer. (codable in BDC)

Front fog lights left warning
• on
• on (alternative)
• off
Warning for malfunction of Front fog lights left in the on board computer. (codable in BDC)

Front fog lights right warning
• on
• off
Warning for malfunction of Front fog lights right in the on board computer. (codable in BDC)

Daytime running lights left warning
• on
• on (alternative)
• on (Japan)
• off
Warning for malfunction of Daytime running lights left in the on board computer. (codable in BDC)

Daytime running lights right warning
• on
• on (alternative)
• on (Japan)
• off
Warning for malfunction of Daytime running lights right in the on board computer. (codable in BDC)

Turn signals rear left warning
• on
• off
Warning for malfunction of Turn signals rear left in the on board computer. (codable in BDC)

Turn signals rear right warning
• on
• off
Warning for malfunction of Turn signals rear right in the on board computer. (codable in BDC)

Standing lights outer rear left warning
• on
• on (alternative)
• off
Warning for malfunction of outer rear left standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights outer rear right warning
• on
• on (alternative)
• off
Warning for malfunction of outer rear right standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights inner rear left warning
• on
• off
Warning for malfunction of inner rear left standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Standing lights inner rear right warning
• on
• off
Warning for malfunction of inner rear right standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Reversing lights left warning
• on
• on (alternative)
• off
Warning for malfunction of left reversing lights in the on board computer. (codable in BDC)

Reversing lights right warning
• on
• on (alternative)
• off
Warning for malfunction of right reversing lights in the on board computer. (codable in BDC)

Rear fog light left warning
• on
• off
Warning for malfunction of rear left fog light in the on board computer. (codable in BDC)

Rear fog light right warning
• on
• off
Warning for malfunction of rear right fog light in the on board computer. (codable in BDC)

Brake lights left warning
• on
• on (alternative)
• off
Warning for malfunction of left braking lights in the on board computer. (codable in BDC)

Brake lights right warning
• on
• on (alternative)
• off
Warning for malfunction of right braking lights in the on board computer. (codable in BDC)

Third brake light warning
• on
• off
Warning for malfunction of third brake light in the on board computer. (codable in BDC)

License plate light warning
• on
• off
Warning for malfunction of license plate lights in the on board computer. (codable in BDC)

Seat belt reminder driver
• on
• off
Seat belt reminder for driver is active/ inactive. (codable in CSM)

Seat belt reminder passenger
• on
• off
Seat belt reminder for passenger is active/ inactive. (codable in CSM)

Seat belt reminder – distance
• 100 m / 330 ft
• 200 m / 660 ft
• 500 m / 0.31 mls
• 1000 m / 0.62 mls
Seat belt reminder is activated after driving the set distance and driving faster than the set speed. Use ‘Seat belt reminder – speed’ to set the speed. (codable in CSM)

Seat belt reminder – speed
• 10 kph / 6 mph
• 20 kph / 12 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
Seat belt reminder is activated after driving the set distance and driving faster than the set speed. Use ‘Seat belt reminder – distance’ to set the distance. (codable in CSM)

Seat belt reminder – duration
• 5s
• 10s
• 30s
• 60s
• 90s
• 100s
• 120s
Duration of seat belt reminder warnings. (codable in CSM)

Seat belt reminder – driver unbuckled
• on
• off
When the driver unbuckles his/her seat belt a short seat belt reminder warning is activated. (codable in CSM)

Seat belt reminder – passenger unbuckled
• on
• off
When the passenger unbuckles his/her seat belt a short seat belt reminder warning is activated. (codable in CSM)

Seat belt reminder – ignition on
• on
• off
When the ignition is turned on and the driver has not put on his/her seat belt a short seat belt reminder warning is activated. (codable in CSM)

Seat belt status display driver
• on
• off
Display of the seat belt status for the driver (buckled/unbuckled) in the dashboard. (codable in CSM)

Seat belt status display passenger
• on
• off
Display of the seat belt status for the passenger (buckled/unbuckled) in the dashboard. (codable in CSM)

Seat belt status display rear seats
• on
• off
Display of the seat belt status for the rear seats (buckled/unbuckled) in the dashboard. (codable in CSM)

Seatbelt Reminder Driver
• on
• off
Deactivate the driver’s acustic seatbelt reminder. To undo the coding run the backup. (codable in GCSMSEATBELTS)

Seatbelt Reminder Passenger
• on
• off
Deactivate the passenger’s acustic seatbelt reminder. To undo the coding run the backup. (codable in GCSMSEATBELTS)

Seatbelt Display Reminder Driver
• on
• off
Deactivate/activate the driver’s optical seatbelt reminder inside KOMBI. (codable in GCSMSEATBELTS)

Seatbelt Display Reminder Passenger
• on
• off
Deactivate/activate the passenger’s optical seatbelt reminder inside KOMBI. (codable in GCSMSEATBELTS)

Welcome lights – standing lights front left
• off
• turn on softly
• turn on hard
Standing lights front left are turned on with welcome lights. (codable in BDC)

Welcome lights – standing lights front right
• off
• turn on softly
• turn on hard
Standing lights front right are turned on with welcome lights. (codable in BDC)

Welcome lights – DRL left
• off
• turn on softly
• turn on hard
Daytime running lights left are turned on with welcome lights. (codable in BDC)

Welcome lights – DRL right
• off
• turn on softly
• turn on hard
Daytime running lights right are turned on with welcome lights. (codable in BDC)

Welcome lights – low beams left
• off
• turn on softly
• turn on hard
Low beams left are turned on with welcome lights. (codable in BDC)

Welcome lights – low beams right
• off
• turn on softly
• turn on hard
Low beams right are turned on with welcome lights. (codable in BDC)

Welcome lights – turn signal front left
• off
• turn on softly
• turn on hard
Turn signal front left are turned on with welcome lights. (codable in BDC)

Welcome lights – turn signal front right
• off
• turn on softly
• turn on hard
Turn signal front right are turned on with welcome lights. (codable in BDC)

Welcome lights – turn signal mid left
• off
• turn on softly
• turn on hard
Turn signal mid (mirrors) left are turned on with welcome lights. (codable in BDC)

Welcome lights – turn signal mid right
• off
• turn on softly
• turn on hard
Turn signal mid (mirrors) right are turned on with welcome lights. (codable in BDC)

Welcome lights – design lights left
• off
• turn on softly
• turn on hard
Design lights left are turned on with welcome lights. (codable in BDC)

Welcome lights – design lights right
• off
• turn on softly
• turn on hard
Design lights right are turned on with welcome lights. (codable in BDC)

Welcome lights – high beams left
• off
• turn on softly
• turn on hard
High beams left are turned on with welcome lights. (codable in BDC)

Welcome lights – high beams right
• off
• turn on softly
• turn on hard
High beams right are turned on with welcome lights. (codable in BDC)

Welcome lights – front fog lights left
• off
• turn on softly
• turn on hard
Front fog lights left are turned on with welcome lights. (codable in BDC)

Welcome lights – front fog lights right
• off
• turn on softly
• turn on hard
Front fog lights right are turned on with welcome lights. (codable in BDC)

Welcome lights – turn signals rear left
• off
• turn on softly
• turn on hard
Turn signals rear left are turned on with welcome lights. (codable in BDC)

Welcome lights – turn signals rear right
• off
• turn on softly
• turn on hard
Turn signals rear right are turned on with welcome lights. (codable in BDC)

Welcome lights – stand. lights outer rear left
• off
• turn on softly
• turn on hard
Outer standing lights rear left are turned on with welcome lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Welcome lights – stand. lights outer rear right
• off
• turn on softly
• turn on hard
Outer standing lights rear right are turned on with welcome lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Welcome lights – stand. lights inner rear left
• off
• turn on softly
• turn on hard
Inner standing lights rear left are turned on with welcome lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in BDC)

Welcome lights – reversing lights left
• off
• turn on softly
• turn on hard
Reversing lights left are turned on with welcome lights. (codable in BDC)

Welcome lights – reversing lights right
• off
• turn on softly
• turn on hard
Reversing lights right are turned on with welcome lights. (codable in BDC)

Welcome lights – rear fog lights left
• off
• turn on softly
• turn on hard
Rear left fog lights are turned on with welcome lights. (codable in BDC)

Welcome lights – rear fog lights right
• off
• turn on softly
• turn on hard
Rear right fog lights are turned on with welcome lights. (codable in BDC)

Welcome lights – braking lights left
• off
• turn on softly
• turn on hard
Braking lights left are turned on with welcome lights. (codable in BDC)

Welcome lights – braking lights right
• off
• turn on softly
• turn on hard
Braking lights right are turned on with welcome lights. (codable in BDC)

Welcome lights – third brake light
• off
• turn on softly
• turn on hard
Third brake light is turned on with welcome lights. (codable in BDC)

Welcome lights – number plate lighting
• off
• turn on softly
• turn on hard
Number plate lights are turned on with welcome lights. (codable in BDC)

Welcome lights
• on
• off
Welcome lights are turned on, when vehicle is unlocked. In order for the welcome light to work, the light switch in the car has to be set to ‘Auto’. In some cases, this option also needs to be enabled in the iDrive. In order to customize which lights should be turned on, please use the following options. (codable in BDC)

Welcome lights – only when dark
• on
• off
Welcome lights are only turned on when the rain-light sensor (RLS) recognizes it is dark outside. Only works if rain-light sensor is installed. (codable in BDC)

Welcome-lights – light switch position
• off
• A
• A or 2
Positions for the light switch where the welcome-lights function is activated. (codable in BDC)

Welcome lights – brightness
• off
• very low
• low
• medium
• high
• very high
Brightness of exterior lights for welcome lights. (codable in BDC)

Welcome lights duration
• 10s
• 20s
• 40s
• 90s
• 150s
• 240s
Duration of the welcome lights in seconds. (codable in BDC)